Mounting a soundbar takes about 30 minutes and requires only a drill, level, and the right wall anchors for your wall type

Hanging a soundbar on the wall is straightforward if you follow the manufacturer's template and use anchors rated for your soundbar's weight. Most soundbars weigh between 2 and 8 pounds, which means standard drywall anchors work for most installations. The key is finding the studs or using heavy-duty anchors, measuring twice, and drilling pilot holes before inserting screws.

This guide walks you through each step so you can mount your soundbar securely without damaging the wall or the unit itself.

Key Takeaways

  • Check your soundbar's manual for the mounting template and weight rating, then choose wall anchors rated for at least that weight.
  • Locate wall studs with a stud finder or use heavy-duty drywall anchors if you cannot mount into studs.
  • Use a level to mark your screw holes so the soundbar hangs straight, and always drill pilot holes before inserting screws.
  • Mount the soundbar below your TV, roughly at ear level when you are seated, for the best sound experience.
  • Hide cables by running them through a cable raceway or behind the wall if you have access to the space behind the drywall.

Gather your tools and check the mounting template

Before you drill anything, open your soundbar's manual and find the mounting template—usually a cardboard insert or a diagram showing exactly where the screw holes go. This template is your most important tool because it ensures the holes are in the right spots. If you cannot find a physical template, check the manufacturer's website and print the PDF version.

Weigh your soundbar or check the manual for its weight. Most soundbars range from 2 to 8 pounds. Write this number down—you will need it to choose the right wall anchors. Gather a drill with a bit slightly smaller than your screws, a level, a tape measure, a pencil, and the anchors or screws that came with your soundbar. If the box did not include anchors, buy ones rated for at least 1.5 times your soundbar's weight.

Decide where to mount and mark the height

The best position for a soundbar is directly below your TV, centered on the wall. Measure the width of your soundbar and find the center point of your TV. Mark this center point lightly with a pencil. Most soundbars sit 6 to 12 inches below the TV, depending on your setup and how much space you have.

Use your level to draw a light horizontal line at the height where the soundbar will sit. This line keeps the soundbar straight and prevents it from tilting. If your TV is mounted high, aim for ear level when you are seated on your couch—this usually means the soundbar sits between 24 and 36 inches from the floor, but adjust based on your room.

Locate studs or choose the right anchors

Use a stud finder to locate the wooden studs behind your drywall. Studs are the strongest mounting points and can hold any soundbar weight without anchors. Mark the stud locations with a pencil. If your mounting holes line up with studs, you are done with this step—just use the screws that came with your soundbar.

If your holes do not hit studs, you will need drywall anchors. Heavy-duty toggle bolts or molly bolts hold 20 to 50 pounds and work well for soundbars. Plastic expansion anchors work for lighter soundbars under 5 pounds but are less reliable. Buy anchors rated for at least 1.5 times your soundbar's weight to leave a safety margin. The package will tell you the maximum weight each anchor holds.

Align the template and drill pilot holes

Tape your mounting template to the wall using the horizontal line you drew as a guide. Make sure the template is level and centered. Use a pencil to mark each screw hole location directly through the template onto the wall. Remove the template and double-check that your marks are level and evenly spaced.

Drill a pilot hole at each mark using a drill bit slightly smaller than your screws. Pilot holes prevent the drywall from cracking and make it easier to insert screws straight. If you are using drywall anchors, drill the hole to the exact size specified on the anchor package—too small and the anchor will not fit, too large and it will not grip. If you hit a stud, you can skip the anchor and go straight to the screw.

Install anchors and mount the soundbar

Insert your drywall anchors into the pilot holes by tapping them gently with a hammer until they sit flush against the wall. Do not force them—they should slide in smoothly. If an anchor is stuck, remove it and check that your pilot hole is the right size. Once all anchors are in place, insert the screws through the soundbar's mounting bracket and into the anchors, tightening by hand first.

Have a helper hold the soundbar level against the wall while you tighten the screws with a drill or screwdriver. Tighten firmly but do not over-tighten—you want the bracket snug against the wall without crushing the drywall or stripping the screw. Once both screws are tight, remove your helper's hands and check that the soundbar does not move or tilt. Use your level one more time to confirm it is straight.

Connect cables and hide the wires

Connect your soundbar to power and to your TV or receiver using the cables that came in the box. Most soundbars use HDMI, optical, or Bluetooth. If your soundbar is wireless, you can skip the cable step. For wired connections, run the cables down the wall and behind your TV stand or entertainment center to hide them.

If you want a cleaner look, use a cable raceway—a plastic channel that sticks to the wall and holds cables inside. Raceways cost $10 to $30 and take 10 minutes to install. Alternatively, if you have access to the space behind the drywall (between studs), you can run cables through the wall using a fish tape, but this requires cutting access holes and is best left to someone with experience.

Frequently Asked Questions

What if my soundbar is too heavy for drywall anchors?

If your soundbar weighs more than 15 pounds, mount it into wall studs using the screws that came with it. Use a stud finder to locate studs, then position your mounting bracket so the screw holes line up with the studs. Studs can hold 50+ pounds without anchors.

Can I mount a soundbar on a plaster or brick wall?

Yes, but you need different anchors. Plaster requires special plaster anchors, and brick requires masonry anchors and a masonry drill bit. Both are available at hardware stores. Masonry anchors are very strong and work well for soundbars on brick or concrete.

How do I know if my soundbar is level after I hang it?

Place a level on top of the soundbar or against its side. The bubble should sit in the center of the level window. If it tilts, loosen one screw slightly and adjust the bracket until the soundbar is level, then tighten again.

What if I drill in the wrong spot?

Fill the hole with spackling paste, let it dry, sand it smooth, and paint over it. Then measure and drill again in the correct location. Mistakes happen—spackling is cheap and takes 20 minutes to dry.

Do I need to turn off my TV before mounting the soundbar below it?

Yes, turn off and unplug your TV before you start drilling. This is a safety precaution in case you accidentally hit a power cable or cause vibrations that affect the TV.