Wall mounting is the most common installation, and the method depends on your wall type and soundbar design
Most soundbars mount to the wall below a TV using either a bracket kit that comes with the soundbar or a universal mounting system you buy separately. The soundbar itself usually has threaded holes on the back or bottom where the bracket attaches. Before you start, check whether your soundbar came with a mounting bracket — many do, but some require you to purchase one. You will also need to know what your wall is made of: drywall, plaster, brick, or tile each require different fasteners.
The basic process is the same across most setups: locate the studs or use appropriate anchors for your wall type, attach the bracket securely, then slide or bolt the soundbar onto the bracket. The entire job usually takes 30 to 45 minutes if you have the right tools and fasteners on hand.
Key Takeaways
- Check your soundbar's manual to see whether it includes a mounting bracket or requires you to buy a universal one separately.
- Find wall studs with a stud finder if mounting into drywall, or use heavy-duty anchors rated for your soundbar's weight if you cannot hit a stud.
- Measure the distance from your TV to the soundbar location and may support cables can reach without stretching or kinking.
- Most soundbars mount 6 to 12 inches below a wall-mounted TV, or directly on a TV stand if the TV sits on furniture.
Gathering the right tools and fasteners before you start
You will need a drill with a bit that matches your fasteners, a level, a tape measure, and a pencil. If your wall is drywall and you cannot hit a stud, buy heavy-duty drywall anchors rated for at least the weight of your soundbar — most soundbars weigh between 3 and 8 pounds, so anchors rated for 25 pounds or more give you a safety margin. If your wall is plaster, use toggle bolts or molly bolts instead, as standard drywall anchors do not hold well in plaster.
For brick or tile, you will need a masonry bit and either masonry anchors or concrete screws. If you are unsure what your wall is made of, drill a small test hole in an inconspicuous spot — the material will tell you when ready. A stud finder costs $15 to $40 and saves time if you plan to mount anything else in the future.
Locating studs and marking your mounting points
Use a stud finder to locate the vertical wooden studs behind your drywall. Mark the center of each stud with a pencil. Studs are typically 16 inches apart. If you find two studs close enough to your desired mounting location, use both — this is the strongest option. If you can only hit one stud, mount the bracket so that at least one hole goes into the stud and the others use heavy-duty anchors.
Measure up from where you want the soundbar to sit and mark the hole locations on the wall. Use a level to may support your marks are perfectly horizontal — a tilted soundbar looks wrong and can cause the bracket to wear unevenly. Double-check your measurements before drilling. If you are mounting below a TV, measure from the bottom of the TV down to where the top of the soundbar should sit, then work backward to find where the bracket holes go.
Drilling holes and installing fasteners
Drill pilot holes at each marked location. A pilot hole is slightly smaller than your fastener and prevents the wall from cracking. If you are drilling into a stud, use a bit slightly smaller than your screw diameter. If you are using drywall anchors, use the bit size recommended on the anchor package — usually printed on the box.
Insert your fasteners: screw directly into studs, or tap drywall anchors into their holes and then screw into the anchors. Tighten firmly but do not over-tighten, which can strip the threads or crack the wall. If you are using toggle bolts or molly bolts in plaster, follow the package instructions — these typically require you to push the anchor through the hole, then tighten a screw that expands the anchor behind the wall.
Attaching the bracket and mounting the soundbar
Screw the mounting bracket to the wall using the fasteners you just installed. Make sure the bracket is level before you tighten the final screws. Most brackets have a slot or rail where the soundbar slides in or bolts down — check your soundbar's manual to see which method yours uses. Slide the soundbar onto the bracket or align the bolt holes and tighten the bolts by hand first, then with a wrench or socket if needed.
Do not overtighten bolts on the soundbar itself, as this can crack the plastic housing. Tighten until snug, then stop. Once the soundbar is mounted, gently push up and down on it to make sure it does not move or rattle. If it does, check that all fasteners are tight and that the bracket is fully seated against the wall.
Routing cables and testing the connection
Run your audio and power cables from the soundbar to your TV, receiver, or wall outlet. Most soundbars use HDMI, optical, or 3.5mm audio cables. Plan your cable route before you mount the soundbar so you know whether the cables will reach. If cables are too short, buy longer ones before mounting — trying to stretch a cable can damage the connectors or pull the soundbar off the bracket.
Use cable clips or adhesive-backed cable holders to keep wires neat and prevent them from hanging visibly. Once cables are connected, power on the soundbar and test the audio. Check that the volume is balanced and that you can hear sound from all channels. If you hear nothing, verify that the input source is correct on both the soundbar and your TV or receiver.
Mounting on a TV stand or furniture instead of a wall
If you do not want to drill into your wall, most soundbars can sit on a TV stand or shelf directly below the TV. Place the soundbar on a stable, level surface and may support it does not block the TV's infrared receiver — the sensor that reads your remote. Leave at least 2 inches of clearance on either side so sound can travel freely.
If the soundbar tends to slide on a smooth surface, use non-slip pads or a rubber mat underneath. This method is faster than wall mounting and lets you move the soundbar later without patching holes. The trade-off is that it takes up shelf or stand space and may look less clean than a wall-mounted setup.
Frequently Asked Questions
Can I mount a soundbar above my TV instead of below it?
Yes, but it is not ideal. Sound travels downward naturally, so a soundbar above your TV will direct audio away from where you are sitting. If space forces you to mount above, angle the soundbar downward if the bracket allows it. Most people find below-TV mounting sounds better.
What if I hit a pipe or wire when drilling?
Stop when ready and do not force the drill. Use a stud finder with a wire and pipe detection mode, or call a professional to locate utilities before you drill. Hitting electrical wiring or plumbing can be dangerous and expensive to repair. When in doubt, ask.
Do I need a stud finder, or can I just tap the wall?
Tapping works for some people, but a stud finder is more reliable, especially in older homes where studs may not be evenly spaced. For the cost and the time saved, a stud finder is worth buying if you plan to mount anything heavier than a picture frame.
How much weight can drywall anchors hold?
Heavy-duty drywall anchors are typically rated for 25 to 50 pounds each. Since most soundbars weigh 3 to 8 pounds, two or three anchors will hold safely. Always buy anchors rated for more than your soundbar weighs, and check the package for the weight rating before you buy.
Can I mount a soundbar on a brick or tile wall?
Yes, but you need the right fasteners. Use a masonry bit to drill into brick or tile, then install masonry anchors or concrete screws. Tile is brittle, so drill slowly and use a bit designed for tile to avoid cracking. If you are unsure, a hardware store employee can recommend the right fasteners for your wall type.