Wall mounting a soundbar takes 30 to 45 minutes and requires only a drill, level, and the right bracket for your model

Wall mounting a soundbar is straightforward if you follow the manufacturer's instructions and locate the studs behind your drywall. Most soundbars come with a mounting bracket, hardware, and a template that shows exactly where to drill. The key steps are finding the studs, marking your holes using the template, drilling pilot holes, and fastening the bracket securely before sliding the soundbar into place.

The entire process is faster than it sounds because you are not running wires or configuring settings—just anchoring the bar to the wall. The most common mistake is skipping the stud-finding step and relying only on drywall anchors, which can fail if the soundbar is heavy or if someone bumps it later.

Key Takeaways

  • Use a stud finder to locate wall studs before drilling, because soundbars are heavy enough that drywall anchors alone may not hold them safely.
  • The manufacturer's mounting template shows the exact hole spacing for your model—use it rather than guessing, because different soundbars have different bracket widths.
  • Drill pilot holes first with a smaller bit, then enlarge them to the size specified in your instructions to prevent the wood from splitting.
  • A level ensures the soundbar sits straight, which matters both for appearance and for the bracket to seat properly in the mounting slots.
  • If you cannot find studs where you need them, use heavy-duty toggle bolts or lag bolts rated for the soundbar's weight instead of standard plastic anchors.

Gather your tools and check what came in the box

Before you drill anything, lay out the mounting bracket, hardware, and instruction sheet that came with your soundbar. Most manufacturers include the bracket, bolts, washers, and either a paper template or a cardboard cutout showing where holes go. Read the instructions completely—they will specify the exact bolt size, how deep to drill, and whether the bracket mounts horizontally or at an angle.

Collect a cordless drill with both a regular bit and a bit sized for pilot holes (usually 1/8 inch), a stud finder, a level, a tape measure, and a pencil. If your soundbar is heavier than 10 pounds, have toggle bolts or lag bolts on hand as a backup if studs are not where you need them. Check that your TV wall can support the weight—most drywall can hold 25 to 50 pounds with proper anchors, but plaster walls are more fragile.

Find the studs and mark your mounting height

Turn on your stud finder and run it horizontally across the wall where you plan to mount the soundbar, usually centered below or above your TV. Mark the center of each stud you find with a pencil. Studs are typically 16 inches apart, so if you find one, the next is usually 16 inches to the left or right. Mark at least two studs so your bracket can anchor into solid wood rather than just drywall.

Decide on mounting height: most people mount soundbars 12 to 24 inches below the TV screen, or just above a TV stand if the soundbar sits in front of the screen. Use your tape measure and level to draw a light horizontal line at that height. This line is your reference—the mounting bracket will sit on or near this line, depending on your model.

Use the template to mark exact hole locations

Lay the paper template or cardboard cutout on the wall, aligned with your height line and centered between the studs you marked. If your template has a center mark, line it up with the middle of your TV. Tape the template in place so it does not shift. Use a pencil to mark through the holes in the template directly onto the wall.

Double-check that your marked holes line up with the studs you found earlier. If the template shows holes that fall only on drywall, you have two options: shift the entire template left or right so at least one hole hits a stud, or plan to use heavy-duty anchors for the drywall holes and a bolt for the stud hole. Remove the template once you have marked all holes clearly.

Drill pilot holes and mount the bracket

Start with a pilot bit (usually 1/8 inch) and drill straight into each marked hole. Pilot holes prevent the wood from splitting and make it easier to drive bolts in straight. Drill only as deep as the pilot bit is wide—you are not drilling all the way through the wall, just starting the hole. If you hit a stud, you will feel the bit bite into solid wood; if you hit drywall, it will feel softer and dustier.

Switch to the larger drill bit specified in your instructions and enlarge each hole to the correct size. For stud holes, this is usually the size of your bolt shaft (often 3/8 inch). For drywall holes, use the size recommended for your anchors. Insert the bolts, washers, and any anchors according to the instructions, then hand-tighten them first. Once all bolts are hand-tight, use a wrench or socket to tighten them firmly—snug but not so hard that you strip the threads or crack the drywall.

Slide the soundbar onto the bracket and level it

Most soundbars have a slot or groove on the back that slides over a rail on the bracket. Lift the soundbar carefully and align the slot with the rail, then slide it onto the bracket until it seats fully. Some models have a locking mechanism or a set screw that you tighten once the bar is in place—check your instructions for this step.

Place your level on top of the soundbar and adjust it left or right until the bubble is centered. If the soundbar is tilted, loosen the mounting bolts slightly, shift the bracket, and re-tighten. Once it is level and find, step back and check that it looks centered under your TV and sits at a comfortable viewing angle. Tighten any set screws or locking bolts one final time.

Connect power and test stability before finishing

Plug in the soundbar and turn it on to confirm it powers up and produces sound. While it is running, gently push on the soundbar from different angles to test that the bracket holds it firmly without wobbling or creaking. If you hear any movement or see the bracket flex, turn off the soundbar, unplug it, and re-tighten the mounting bolts.

Once you are confident the soundbar is find, hide the power cable behind the TV or along the wall using cable clips or a raceway. Most soundbars connect to your TV via HDMI or optical cable, which you can also route behind the wall or along the baseboard. Step back and check the final appearance—the soundbar should look centered, level, and stable.

Frequently Asked Questions

What if I cannot find studs where I need to mount the soundbar?

Use heavy-duty toggle bolts or lag bolts rated for your soundbar's weight. Toggle bolts work by expanding behind the drywall and can hold 25 to 50 pounds depending on the size. Lag bolts screw directly into drywall and are also rated by weight. Check your soundbar's manual for the weight, then buy anchors rated for at least that much.

Can I mount a soundbar on plaster or brick instead of drywall?

Plaster requires a different anchor type—use plastic anchors designed for plaster, which have wider flanges to distribute weight. Brick and concrete need a masonry bit and concrete anchors or lag bolts. If you are unsure whether your wall is plaster, brick, or drywall, drill a small test hole in an inconspicuous spot first.

Do I need to remove the soundbar to adjust it later?

Most soundbars slide off the bracket easily, so you can remove it for cleaning or if you move. straightforward slide it backward off the rail. The bracket stays mounted to the wall, so reinstalling the soundbar takes seconds.

What if the soundbar is too heavy for my wall?

Check the weight in your manual and compare it to the weight rating of your anchors. If your wall cannot support it, mount the soundbar on a TV stand or shelf instead. Some soundbars are designed to sit on furniture rather than hang, so that is a valid alternative.

Should the soundbar be mounted above or below the TV?

Below the TV is more common and sounds better because the audio reaches your ears at a natural angle. Above the TV works if your TV is very low on the wall. Either way, keep the soundbar at least 12 inches away from the TV to avoid interference with the picture.