The three ways to mount a soundbar

You can mount a soundbar to your TV in three ways: on the wall above or below the screen, on a TV stand or shelf directly beneath the TV, or on a bracket that attaches to the TV's VESA mounting points. Wall mounting looks cleanest but requires drilling into drywall and running cables. Stand mounting is the easiest and requires no tools beyond what came in the box. Bracket mounting sits the soundbar directly on the TV frame and works only if your TV has a VESA pattern — a grid of threaded holes on the back — and if the soundbar's bracket is designed for that pattern.

The right choice depends on your TV setup, your wall material, and how much cable management you want to do. Most people choose stand mounting because it avoids drilling and works with any TV. Wall mounting is the second choice when you want the soundbar hidden and your wall can support it. Bracket mounting is least common because it limits where you can place the soundbar and adds weight directly to the TV.

Key Takeaways

  • Stand mounting requires no drilling or special tools and works with any TV, but the soundbar sits below the screen and takes up shelf space.
  • Wall mounting looks cleanest and frees up shelf space, but you need to locate studs, drill holes, and route cables, and your wall must be drywall or plaster — not tile or brick.
  • Bracket mounting attaches the soundbar directly to your TV's VESA mounting holes, but only works if your TV has VESA holes and the soundbar's bracket matches that pattern.
  • Before you start, check your soundbar's manual for the mounting pattern, weight limit, and whether it comes with a bracket or requires you to buy one separately.
  • Cable routing matters as much as the mount itself — plan where your power cord and HDMI or optical cable will run before you drill or install.

Stand mounting: the easiest option

Stand mounting means placing the soundbar on a TV stand, shelf, or table directly in front of or below your TV. This requires no tools, no drilling, and no permanent changes to your home. The soundbar sits on its own feet or on a small stand that came in the box. You plug in the power cord, connect the audio cable (HDMI, optical, or Bluetooth), and you are done.

The trade-off is that the soundbar takes up shelf or stand space, and it sits below the TV rather than flush with it. If your TV stand is narrow or already crowded, the soundbar may overhang or block vents on your equipment. Check the soundbar's width and depth against your stand before you buy. If the soundbar is wider than your stand, it will sit in front of the stand and may look awkward or block your view of the screen's bottom edge.

Stand mounting is the best choice if you rent, if you move frequently, or if you want to avoid drilling. It is also the best choice if your wall is concrete, brick, tile, or plaster — materials that are hard to drill or that you cannot damage.

Wall mounting above or below the TV

Wall mounting means fastening the soundbar to the wall with brackets and screws. The soundbar hangs on the wall either above the TV (less common) or below it (more common). This frees up shelf space and looks clean, but it requires drilling into studs, running cables, and having the right wall material.

Before you drill, locate the studs in your wall using a stud finder. Soundbars are heavy — most weigh between 3 and 8 pounds — and drywall alone cannot hold that weight. You must screw into the wooden studs behind the drywall. Mark the stud locations with a pencil, then hold the soundbar bracket against the wall and mark the screw holes. Drill pilot holes (smaller holes that guide the screws) at those marks, then screw the bracket into the studs. The soundbar then clips or slides onto the bracket.

After mounting, you need to route the power cord and audio cable down the wall. You can run them behind the TV, through a cable raceway (a plastic channel that hides wires), or along the wall edge if your TV is on a stand. If you are mounting the soundbar above the TV, cables are easier to hide because they run down behind the screen. If you are mounting below the TV, cables must run down to a receiver, amplifier, or power outlet, which may be visible.

Wall mounting does not work on concrete, brick, or tile unless you use special anchors designed for those materials — and even then, the weight limit is lower. Check your soundbar's manual for the maximum weight it can support on the wall, and confirm that your anchors are rated for that weight.

Bracket mounting directly to the TV

Some soundbars come with a bracket that attaches to your TV's VESA mounting holes — the threaded holes on the back of the TV that are normally used for wall mounts. The soundbar bracket screws into those holes, and the soundbar hangs from the bracket. This keeps the soundbar close to the TV and looks integrated.

Bracket mounting only works if your TV has VESA holes and if the soundbar's bracket is designed for your TV's VESA pattern. VESA patterns are measured in millimeters — common patterns are 100x100, 200x200, and 300x300. Check your TV's manual or the back of the TV to find its VESA pattern, then check the soundbar's manual to see which patterns its bracket supports. If the patterns do not match, the bracket will not fit.

Even if the patterns match, bracket mounting adds weight to the TV and can stress the TV's frame, especially on large or thin TVs. Some TV manufacturers warn against using VESA holes for anything other than wall mounts. Read your TV's manual before you use a bracket mount. If your TV is mounted on a stand rather than a wall, the extra weight of the soundbar on the VESA holes may cause the TV to tip forward.

Bracket mounting also limits where you can place the soundbar — it must sit directly on the TV frame, which may be too high or too low for optimal sound. For these reasons, bracket mounting is the least common choice.

Tools and hardware you will need

For stand mounting, you need nothing beyond what came in the soundbar box — usually just the soundbar itself and a power cord.

For wall mounting, you need a stud finder, a drill with a drill bit set, a level, a tape measure, and a pencil. You also need the correct wall anchors and screws for your wall type. Drywall requires wood screws and studs. Plaster requires plaster anchors. Concrete and brick require concrete anchors or a hammer drill. Your soundbar's manual should specify the screw size and weight rating. If it does not, take the manual and a photo of the mounting bracket to a hardware store and ask the staff to recommend the right fasteners.

For bracket mounting, you need a screwdriver that fits the VESA holes on your TV. Most VESA holes use Phillips-head or hex screws. The soundbar manual should include the screws and bracket, but check before you buy.

Cable routing and power placement

Before you mount the soundbar, plan where the power cord and audio cable will run. A power cord that hangs visibly down the wall or across your TV stand looks messy and can be a tripping hazard. An audio cable that is too short or routed awkwardly can stress the connection and cause dropouts.

For wall mounting, run the power cord down the wall behind the TV if possible. If your TV is on a stand, the cord can run behind the stand and down to a power outlet. If your outlet is far from the TV, use a power strip mounted to the wall or stand to shorten the visible cord run. For audio, use HDMI or optical cable if your soundbar supports it — these are more reliable than Bluetooth over long distances. Run the cable down the wall alongside the power cord, or through a cable raceway.

For stand mounting, the power cord and audio cable can run behind the stand or along the wall. If the soundbar is on a shelf, route cables down the back of the shelf or through a hole in the shelf if one exists. Avoid running cables across the front of the stand where they are visible and where people might trip on them.

Checking weight limits and wall strength

Every soundbar has a weight limit for wall mounting, listed in the manual. This is the maximum weight the bracket can safely hold. Most soundbars weigh 3 to 8 pounds, which is light enough for standard drywall anchors if you screw into studs. However, if your soundbar is heavier or if your wall is weak (old plaster, thin drywall, or water damage), you may need stronger anchors or professional installation.

To test wall strength, press hard on the wall near where you plan to mount the soundbar. If the wall feels soft, spongy, or moves, it may have water damage or poor backing. Do not mount the soundbar there. If you are unsure, drill a test hole in an inconspicuous spot and feel the resistance. Solid drywall over a stud should feel firm and require steady pressure to drill through. If the drill spins easily or feels mushy, the wall may not be suitable for mounting.

If your wall is weak or you are uncomfortable drilling, stand mounting or professional installation is the safer choice.

Frequently Asked Questions

Can I mount a soundbar above my TV instead of below it?

Yes, but it is less common. Sound travels downward and forward, so a soundbar above the TV may sound like it is coming from above the screen rather than from the screen itself. Most people prefer mounting below the TV for better sound localization. If you must mount above, position it as close to the screen as possible and angle it downward slightly.

What if my TV does not have VESA holes?

Older TVs and some budget models do not have VESA holes. In that case, bracket mounting is not an option. Use stand mounting or wall mounting instead. Wall mounting is independent of the TV and works with any TV.

Do I need to turn off the TV before mounting a soundbar to it?

Yes. Turn off the TV and unplug it from the wall before you attach a bracket to the VESA holes. This prevents electrical shock and protects the TV's internal circuits. For wall mounting, you do not need to turn off the TV, but it is safer to do so while you are drilling nearby.

Can I mount a soundbar on a plaster wall?

Yes, but plaster is more brittle than drywall and cracks easily. Use a stud finder to locate studs, and screw into the studs whenever possible. If you must screw into plaster between studs, use plaster anchors rated for the soundbar's weight. Drill slowly and use a drill bit designed for plaster, not drywall.

What is the best height to mount a soundbar on the wall?

Mount the soundbar at ear level when you are sitting on your couch, or just below the TV screen. If the soundbar is too high, sound will travel over your head. If it is too low, it may be blocked by furniture or people sitting in front of it. Most people mount it 12 to 24 inches below the TV screen, depending on the TV size and seating distance.