The Basic Steps for Wall-Mounting a Soundbar
Most soundbars mount to the wall using a bracket that comes in the box or can be bought separately, anchors that grip drywall, and screws. You locate the studs behind your drywall (or use heavy-duty anchors if you cannot hit studs), drill pilot holes, screw the bracket to the wall, then slide or bolt the soundbar onto the bracket. The whole job takes 20 to 45 minutes if you have a drill and a stud finder, and costs nothing beyond what you already own unless you need to buy anchors or a bracket.
The real decisions are where to mount it—usually below or above your TV—and whether to run the cable behind the wall or along the surface. Both are straightforward, but the cable routing affects how much prep work you do upfront.
Key Takeaways
- Most soundbars come with a mounting bracket and hardware; check your box before buying extras.
- Mounting into wall studs is strongest, but heavy-duty drywall anchors work if studs are not in the right spot.
- Measure twice and mark your holes with a pencil before drilling to avoid mistakes in drywall.
- Run power and audio cables before you mount the soundbar if you want them hidden behind the wall.
- A stud finder ($15 to $40) saves time and prevents drilling into empty drywall.
Gather Your Tools and Check What Comes in the Box
Open your soundbar box and lay out everything. Most soundbars ship with a wall-mounting bracket, a set of screws, and sometimes plastic anchors or metal toggle bolts. Read the manual to confirm what hardware is included and what the bracket is rated to hold—this matters because a heavy soundbar (some weigh 5 to 8 pounds) needs stronger anchors than a light one.
You will need a drill with a drill bit slightly smaller than your screws, a level, a tape measure, a pencil, and ideally a stud finder. If your soundbar did not come with a bracket, you can buy a universal soundbar bracket online for $20 to $50. If you are mounting into drywall without studs, pick up heavy-duty anchors rated for at least twice the weight of your soundbar—toggle bolts or molly bolts hold better than plastic expansion anchors.
Find the Right Height and Location
The most common spot is on the wall directly below your TV, centered and about 12 inches below the screen. If your TV is mounted high, you can mount the soundbar above it instead, though this is less common because it points sound upward. Measure from the center of your TV to find the center of where the soundbar will go, then use your level to mark a horizontal line at the height you want.
Before you drill, hold the bracket up to the wall and mark the screw holes with a pencil. Step back and look at it—make sure it is level and centered. This is the moment to catch mistakes, not after you have drilled four holes.
Locate Studs or Decide on Anchors
Use a stud finder to scan the wall horizontally across your marked line. Most stud finders beep or light up when they cross a stud. Mark the stud locations with a pencil. If studs line up with your bracket holes, you are done—drill into the studs. If not, you have two choices: move the bracket to hit studs, or use heavy-duty drywall anchors.
Heavy-duty anchors work fine for soundbars under 10 pounds. Toggle bolts and molly bolts grip the back of the drywall and hold much better than plastic anchors. If you go this route, drill the holes to the size specified on the anchor package, then install the anchors before screwing the bracket in place.
Drill Pilot Holes and Mount the Bracket
Use a drill bit slightly smaller than your screws to drill pilot holes at each mark. Pilot holes prevent the drywall from cracking and make screwing easier. If you are drilling into studs, a smaller bit still helps. Drill straight in—use a level or a square to keep the drill perpendicular to the wall.
Once the pilot holes are drilled, screw the bracket to the wall by hand first, then tighten with a drill on low speed. Do not overtighten—you want the bracket snug, not stripped. If you are using anchors, install them first, then screw the bracket into the anchors.
Route Cables Before You Mount the Soundbar
Before you slide the soundbar onto the bracket, decide where the power cord and audio cable will go. If you want them hidden, run them behind the wall now. Drill a hole in the wall at the top of your TV stand or cabinet, feed the cables through, and tape them to the back of the wall studs with painter's tape so they stay in place. This is much easier to do before the soundbar is mounted.
If you are running cables behind the wall, use a fish tape or a coat hanger to pull them through, and label both ends with tape so you know which is which when you pull them out the other side. If you prefer cables on the surface, use cable clips or a cable raceway to keep them neat and out of sight.
Slide or Bolt the Soundbar Onto the Bracket
Most brackets have a slot or rail that the soundbar slides into, then a bolt or screw that locks it in place. Some brackets bolt directly to the soundbar. Check your manual for the exact method. Slide the soundbar onto the bracket slowly and make sure it sits level. Tighten any locking bolts or screws, but again, do not overtighten.
Plug in the power cord and audio cable, turn on the soundbar, and test the sound. If it sounds muffled or off, check that the audio cable is fully seated in the jack. If the soundbar is not level, loosen the bracket bolts slightly, adjust, and retighten.
Frequently Asked Questions
Can I mount a soundbar on a plaster or brick wall?
Yes, but the method is different. Plaster requires special anchors designed for plaster, and brick requires a masonry bit and concrete anchors. Both are stronger than drywall anchors, so a soundbar will hold securely. A hardware store can recommend the right anchors for your wall type.
What if I cannot find a stud where I need to mount?
Use heavy-duty toggle bolts or molly bolts rated for at least twice your soundbar's weight. These grip the back of the drywall and hold as well as studs for most soundbars. If your soundbar is very heavy (over 10 pounds), move the bracket to hit a stud, or hire a professional to run a support beam.
Do I need to hide the cables behind the wall?
No. Running cables behind the wall looks cleaner but takes extra work and requires drilling holes. Cable clips or a cable raceway on the surface is faster and easier, and you can always hide them behind furniture or paint them to match the wall.
What if the soundbar is not level after I mount it?
Loosen the bolts that hold the soundbar to the bracket, adjust it until a level shows it is straight, then retighten. If the bracket itself is not level, loosen the bracket screws, adjust the bracket, and retighten those too.
Can I mount a soundbar above my TV instead of below?
Yes, but sound will point upward instead of toward you, so the audio will not be as direct. Below the TV is the standard spot because it aims sound at ear level. Above works if your TV is very low and you have no other option.