Connect the soundbar to your TV first

The soundbar connects to your TV using one cable, and that cable is almost always HDMI. Look at the back of your TV for a port labeled HDMI — there are usually several. Pick any one and plug the HDMI cable from the soundbar into it. The other end of that cable goes into the HDMI port on the back of the soundbar itself.

If your TV is older and has no HDMI ports, or if the HDMI port is already full, you can use an optical audio cable instead. Optical ports look like small square holes with a door that slides open. Both your TV and soundbar will have one if they support it. Plug one end into the TV's optical out port and the other into the soundbar's optical in port.

Once the cable is connected, turn on your TV and soundbar. Your TV should automatically detect the soundbar and send sound to it. If you still hear sound from the TV's built-in speakers, go into your TV's settings menu, find the audio or sound output option, and select the soundbar from the list.

Key Takeaways

  • HDMI is the standard connection — plug one end into your TV and the other into the soundbar, then select the soundbar as your audio output in the TV's settings.
  • Optical audio cable works as a backup if HDMI ports are full, though HDMI carries better sound quality.
  • Place the soundbar on a TV stand or wall-mounted below the TV, centered and at ear level when you are sitting down.
  • Wireless subwoofers and rear speakers pair to the soundbar using a pairing button, usually held for three seconds until a light blinks.
  • Run the soundbar's setup menu to configure surround speakers and subwoofer volume, which takes five to ten minutes.

Position the soundbar for the best sound

The soundbar works best when it sits directly below your TV, centered on the wall or TV stand. If your TV is mounted high on the wall, mount the soundbar below it at roughly ear level when you are sitting on your couch — not on the floor. Sound travels in a straight line, so a soundbar at ear level reaches your ears more directly than one pointing upward from the floor.

Keep the soundbar at least a few inches away from walls on either side. Sound bounces off hard surfaces, and walls on both sides can create an echo or muddy the audio. If the soundbar sits in a cabinet or enclosed space, leave the front open so sound can travel freely into the room.

Avoid placing the soundbar behind a closed cabinet door or inside a shelf with a back panel. Even a thin door blocks enough sound to make the soundbar sound muffled. If you must hide it, use an open shelf or a stand with no back.

Pair wireless subwoofers and rear speakers

Most soundbars come with a wireless subwoofer, and many include rear speakers for surround sound. These pair to the soundbar automatically when you first turn everything on, but if they do not, you can pair them manually. Look for a small pairing button on the back of the subwoofer or rear speaker — it is usually recessed so you need a pen or paperclip to press it.

Press and hold the pairing button for three seconds until a light on the device starts blinking. Then press the pairing button on the soundbar itself, or go into the soundbar's menu and select "Pair Subwoofer" or "Pair Speakers." The devices will find each other within a minute or two, and the blinking light will stop once they are connected.

Place the subwoofer in a corner of the room or against a wall — corners amplify bass naturally, so you will get deeper sound with less effort. Keep it away from your seating area if possible; bass is felt more than heard, and a subwoofer right next to you can feel overwhelming. Rear speakers should sit on shelves or stands behind your couch, roughly at ear level.

Run the soundbar's setup menu

Once everything is connected and paired, open the soundbar's setup menu using the remote control. Look for a button labeled Menu, Settings, or Setup. The menu will walk you through a few basic steps: confirming that the subwoofer is connected, setting the subwoofer volume, and positioning rear speakers if you have them.

For subwoofer volume, start at the middle setting and adjust it after a few days of listening. Bass that sounds good on the first day often feels too strong after a week. Many soundbars also have a "calibration" or "auto-detect" option that listens to the room and adjusts the sound automatically — run this if your soundbar offers it.

If your soundbar has rear speakers, the menu will ask you to confirm they are connected. Once confirmed, you can adjust the rear speaker volume separately from the main soundbar. Start with the rear speakers at a lower volume than the front — they should add depth without overwhelming the main dialogue and music.

Adjust audio settings on your TV

After the soundbar is set up, go into your TV's audio settings and turn off any surround sound processing. Most TVs have options like "Dolby Digital" or "DTS" that your TV applies before sending sound to the soundbar. The soundbar has its own processing, and letting both run at once can create odd effects or make dialogue sound unclear.

Look for a setting called "PCM" or "Stereo" and select that instead. PCM is raw, unprocessed sound — the soundbar will handle all the surround processing itself. If your TV has a setting for "HDMI audio format," set it to "Auto" and let the soundbar and TV negotiate the best format.

Some TVs also have a "TV Speaker" setting. Make sure it is set to "Off" so sound comes only from the soundbar, not from both the TV and the soundbar at once.

Connect to streaming services and gaming consoles

If you have a streaming device like a Roku, Apple TV, or Fire Stick, plug it into an HDMI port on the soundbar instead of directly into the TV. The soundbar will pass the video signal through to the TV while handling the audio itself. This is called HDMI passthrough, and it simplifies your setup because everything goes through the soundbar.

Gaming consoles like PlayStation or Xbox should also connect to the soundbar's HDMI port. Make sure the console's audio output is set to "HDMI" in its settings, not "Optical" or "Headphone." Once connected, the console will send both video and audio through the soundbar to your TV.

If you run out of HDMI ports on the soundbar, use an HDMI splitter or switch — a small device that lets you plug multiple cables into one port. Avoid using the TV's HDMI ports for streaming devices if possible, because sound will go to the TV first and then to the soundbar, adding a slight delay.

Test the soundbar with different content

After setup is complete, test the soundbar with a few different types of content. Watch a movie with surround sound to hear how the rear speakers work. Listen to music to check that the midrange and treble sound clear. Play a game or watch a sports broadcast to hear how the subwoofer handles fast action and impact sounds.

If dialogue sounds muffled or hard to understand, the subwoofer volume is probably too high — lower it by a few notches. If you cannot hear rear speakers at all, check that they are actually paired and that their volume is not set to zero in the menu. If the soundbar sounds thin or lacks bass, raise the subwoofer volume slightly.

Most soundbars take a few days to sound right as your ears adjust to the new audio. Avoid making big changes on the first day. Instead, listen for a week and then make small adjustments if needed.

Frequently Asked Questions

Do I need to use HDMI, or can I use Bluetooth?

HDMI is better because it carries higher-quality audio and does not have the slight delay that Bluetooth can introduce. Bluetooth is useful as a backup for playing music from your phone, but for TV and movies, HDMI is the standard connection. Most soundbars support both.

What if my soundbar has no subwoofer included?

You can buy a wireless subwoofer separately and pair it to the soundbar using the same pairing button method. Make sure the subwoofer is made by the same brand as your soundbar — third-party subwoofers sometimes work, but the pairing process can be unpredictable. Check the soundbar's manual to see which subwoofers are compatible.

Can I mount the soundbar on the wall instead of on a stand?

Yes, most soundbars come with a wall-mounting bracket. Mount it below the TV at ear level, centered on the wall. Use a stud finder to locate the wooden studs behind the drywall, and screw the bracket into the studs — do not rely on drywall anchors alone, because soundbars are heavy. If you cannot find studs in the right spot, use heavy-duty toggle bolts rated for the soundbar's weight.

Why is there a delay between the sound and the picture?

This usually happens when the soundbar is processing the audio. Go into the soundbar's menu and look for a "lip sync" or "audio delay" setting. Increase the delay by small amounts — usually in 20-millisecond steps — until the sound matches the picture. Most soundbars remember this setting once you save it.

Do I need to update the soundbar's firmware?

Check the soundbar's menu for a "Software Update" or "Firmware Update" option. If an update is available, run it while the soundbar is plugged in and connected to your Wi-Fi. Updates usually add features or fix bugs, so it is worth doing once after setup, but you do not need to check constantly.