Clean your Euhomy ice maker by running the built-in cleaning cycle, then manually washing the water reservoir and ice basket

Your Euhomy ice maker has a self-cleaning function that flushes the internal water lines—this is the fastest way to remove mineral buildup and keep the machine running smoothly. The cleaning cycle takes about 30 minutes and uses only water. After the cycle finishes, you'll wash the removable parts by hand. Most owners do this once a month, or more often if you have hard water.

The whole process takes less than an hour and requires no special tools or cleaning chemicals. You don't need to take the machine apart or call a technician for routine maintenance.

Key Takeaways

  • The cleaning cycle button on your Euhomy runs automatically and clears mineral deposits from the water lines without any chemicals.
  • You must empty the ice basket and water reservoir before starting the cleaning cycle, or the machine will not run it.
  • After the cycle finishes, wash the water reservoir, ice basket, and ice scoop with warm soapy water and dry them completely before reassembling.
  • Hard water causes faster mineral buildup, so if your tap water is hard, run the cleaning cycle every two weeks instead of monthly.

Running the built-in cleaning cycle

Start by emptying the ice basket completely. Press and hold the Cleaning button on the front panel for three seconds until you hear a beep. The display will show "Cleaning" and the machine will begin running water through the internal lines. Do not open the door or press any buttons while the cycle is running.

The cycle takes about 30 minutes. During this time, water flows through the ice-making mechanism and drains into a collection tray at the bottom of the machine. You will hear water running and occasional mechanical sounds—this is normal. When the cycle finishes, the machine will beep three times and the display will return to the normal ice-making screen.

If the cleaning cycle does not start, check that the water reservoir is full. The machine will not run the cycle if the water level is too low. Fill the reservoir to the line marked "Max" and try again.

Emptying and washing the water reservoir

After the cleaning cycle finishes, locate the water reservoir at the back of the machine. It is a clear plastic container that slides out toward you. Grasp it firmly and pull it straight out—do not tilt it or you may spill water inside the machine.

Empty any remaining water into a sink. Rinse the reservoir under warm running water, then fill it halfway with warm water and add a few drops of dish soap. Swish the soapy water around the inside to loosen any sediment or algae, then rinse thoroughly under running water until no soap remains. Dry the outside and inside completely with a clean cloth before sliding it back into place.

If you see white, chalky deposits stuck to the inside of the reservoir, fill it with equal parts white vinegar and water, let it sit for 30 minutes, then scrub gently with a soft brush or cloth. Rinse very thoroughly afterward, as vinegar smell can transfer to your ice if not rinsed completely.

Cleaning the ice basket and scoop

Remove the ice basket by lifting it straight up and out of the machine. Empty any ice into a sink or trash. Wash the basket with warm soapy water, paying special attention to the corners where ice can stick. Rinse well and dry completely with a cloth.

The ice scoop should also be washed with warm soapy water and dried. Do not put either the basket or scoop in the dishwasher, as the heat can warp the plastic. Store them in a clean, dry place until you reassemble the machine.

Reassembling the machine and running a test cycle

Slide the water reservoir back into its slot until you hear it click into place. Set the ice basket back into the machine, making sure it sits flat on the bottom. The basket should not rock or shift when you gently push it.

Fill the water reservoir to the "Max" line with fresh water. Press the power button to turn the machine on. It will take 5 to 10 minutes to make the first batch of ice after cleaning. Once ice begins dropping into the basket, your machine is working correctly. Discard the first batch of ice and use the second batch, as the first batch may contain residual water from the cleaning cycle.

Common mistakes that slow down cleaning

The most common mistake is not drying the water reservoir completely before putting it back. Even small amounts of water left inside can drip into the machine and cause the next cleaning cycle to fail. Wipe the inside and outside thoroughly with a dry cloth.

Another mistake is running the cleaning cycle when the water reservoir is not full. The machine needs a full reservoir to push water through all the internal lines. If the cycle stops partway through, empty the reservoir, refill it to "Max," and start the cycle again.

Do not use vinegar or other cleaning chemicals in the water reservoir during the cleaning cycle. The Euhomy is designed to use water only. Chemicals can damage the internal seals and leave a taste in your ice.

When to clean more or less often

If your tap water is soft or filtered, you can run the cleaning cycle every six weeks. If you have hard water (water that leaves white spots on dishes or feels slippery), run it every two weeks. You can tell you have hard water if you see white, chalky buildup inside the water reservoir or if the machine takes longer than usual to make ice.

If your Euhomy sits unused for more than two weeks, run the cleaning cycle before making ice again. Stagnant water in the lines can develop odors or algae growth, and the cleaning cycle will flush it out.

Frequently Asked Questions

Can I use vinegar to clean the inside of my Euhomy ice maker?

Vinegar should only be used on the water reservoir itself, not in the cleaning cycle. Fill the reservoir with equal parts vinegar and water, let it soak for 30 minutes, scrub gently, and rinse very thoroughly. Never pour vinegar into the machine's water inlet, as it can damage internal seals and leave a vinegar taste in your ice.

Why is my ice maker making ice slowly after cleaning?

The most common cause is that the water reservoir is not filled to the "Max" line. Fill it completely and wait 10 to 15 minutes for the machine to resume normal speed. If it is still slow, run the cleaning cycle again. Slow ice production usually means mineral buildup is blocking the water lines.

What if the cleaning cycle button does not work?

Make sure the water reservoir is full and the machine is powered on. Press and hold the Cleaning button for a full three seconds—a short press will not start the cycle. If the button still does not respond, unplug the machine for 30 seconds, plug it back in, and try again.

Do I need to drain the machine before cleaning it?

No. The cleaning cycle automatically drains water through the collection tray at the bottom. You only need to empty the ice basket and make sure the water reservoir is full. After the cycle finishes, empty the collection tray if water has pooled there.

How do I know if my ice maker needs cleaning?

Signs include ice that takes longer than usual to form, a musty or stale smell from the ice, or white deposits visible inside the water reservoir. If you notice any of these, run the cleaning cycle right away. Regular monthly cleaning prevents these problems from developing.