The fastest way to reset your GE Profile ice maker
Most GE Profile ice makers reset by holding the reset button for three to five seconds. The reset button is usually located on the ice maker itself — look for a small button marked "Reset" or "Test" on the front or side of the unit, inside your freezer. Hold it until you hear a chime or see a light blink, then release. The ice maker will drain any water in the line, pause for a few minutes, and start a new cycle.
If you cannot find a physical reset button, your model may reset through the refrigerator's control panel instead. Check the display on the front of your fridge for an "Ice Maker" or "Reset" option in the menu — the exact name varies by model year. Press it and hold for three to five seconds the same way.
After you reset, the ice maker will take 24 hours to produce its first batch of ice. During that time, it fills the mold, freezes, and ejects. Do not open the freezer door repeatedly during this period, as it slows the cycle.
Key Takeaways
- The reset button on GE Profile ice makers is usually on the ice maker unit itself, inside the freezer, and requires a three to five second hold.
- Some models have no physical button and reset instead through the refrigerator's front control panel menu.
- After reset, allow 24 hours for the ice maker to complete its first full cycle and produce ice.
- If the ice maker does not cycle after reset, check that the water supply line is connected and the freezer temperature is at or below 0°F.
- A reset clears error codes and restarts the machine, but does not fix mechanical failures like a broken ejector arm or frozen water line.
When to reset instead of calling for repair
A reset is the right first step when your ice maker stops producing ice, produces small or hollow cubes, or shows an error code on the display. It is also worth trying if the ice maker runs but does not eject ice, or if it has not been used in several months and you want to clear old settings.
Do not expect a reset to fix a frozen water line, a cracked ice bucket, a broken ejector arm, or a compressor that has failed. If you reset and the ice maker still does not cycle after 24 hours, or if it cycles but produces no ice, the problem is mechanical or electrical and requires a technician.
Check the water supply before you reset
Before you reset, confirm that water is reaching the ice maker. Look at the water supply line — it is usually a thin plastic or copper tube running from the back of the refrigerator to the ice maker. Make sure it is not kinked, pinched, or disconnected at either end.
If the line looks intact, turn off the water supply valve behind the refrigerator (it is usually a small knob or lever on the wall) and disconnect the line at the refrigerator end. Hold a cup under the end of the line and turn the valve back on for a few seconds. If water flows, the supply is working. If no water comes out, the line is blocked or the valve is closed — turn the valve off again and call a technician.
Also check that your freezer temperature is at or below 0°F. If it is warmer, the ice maker will not freeze water into cubes. Adjust the freezer dial and wait 24 hours for the temperature to stabilize before you reset.
Step-by-step reset for GE Profile models with a physical button
Locate the reset button on the ice maker unit. On most GE Profile models, it is a small round or rectangular button on the front face of the ice maker, sometimes labeled "Reset" or "Test." If you do not see it on the front, check the side or back of the unit — you may need to remove the ice bucket to see it clearly.
Press and hold the button for three to five seconds without releasing. You should hear a beep or see a light flash on the ice maker. This signals that the reset has started. Release the button and listen for the sound of water flowing into the mold — this happens within a few seconds of a successful reset.
Close the freezer door and leave the ice maker alone for at least 24 hours. Do not open the door to check on it. The ice maker will go through a full cycle: fill, freeze, and eject. After 24 hours, you should see ice in the bucket.
Reset through the refrigerator control panel
If your GE Profile model does not have a physical reset button on the ice maker, the reset function is in the refrigerator's menu. Press the button or touch the screen on the front of your fridge labeled "Menu," "Settings," or "Control Panel" — the exact label depends on your model year.
Navigate to "Ice Maker" or "Icemaker" in the menu using the arrow buttons or touchscreen. You should see options like "On," "Off," or "Reset." Select "Reset" and hold the button for three to five seconds, or press "Confirm" if the display asks you to confirm the action.
The display will show a message like "Resetting" or "Ice Maker Reset" for a few seconds, then return to the main menu. Close the menu and close the freezer door. The ice maker will begin its cycle within a few minutes.
What happens during the reset cycle
When you reset a GE Profile ice maker, the machine goes through a diagnostic and cleaning cycle. First, it drains any water sitting in the fill tube or mold from the previous cycle. Then it pauses for two to three minutes while the system resets its internal timer and sensors.
After the pause, the ice maker fills the mold with fresh water. This takes about 10 to 15 seconds. The freezer then freezes the water solid, which takes several hours depending on your freezer temperature. Once frozen, the ejector arm pushes the cubes into the bucket. The whole process from reset to first ice takes 24 hours.
If you hear water running but no ice appears after 24 hours, the water is not freezing — usually because the freezer is too warm or the water line is blocked. If you hear nothing at all, the reset did not take or the ice maker has a power or sensor problem.
Troubleshooting if the reset does not work
If the ice maker does not cycle after you reset, first check that the ice maker is turned on. Look for an "On/Off" switch on the ice maker unit itself, or check the control panel menu to confirm the ice maker is set to "On" rather than "Off." Some models have a small lever or switch that can be bumped to the off position by accident.
Next, confirm the freezer temperature again. Use a thermometer inside the freezer to check — the dial setting is not always accurate. If the temperature is above 0°F, adjust the freezer dial to a colder setting and wait 24 hours. Then reset again.
If the ice maker still does not cycle, check the water supply line one more time. Disconnect it at the refrigerator end and run water through it into a cup to confirm flow. If water flows but the ice maker still will not cycle after reset, the problem is inside the ice maker — a frozen fill tube, a broken solenoid valve, or a sensor failure — and you will need a technician.
Frequently Asked Questions
How long does it take for ice to appear after I reset?
The first batch of ice appears 24 hours after reset. The ice maker fills the mold when ready, but it takes most of that time to freeze solid and eject. Do not open the freezer repeatedly during this period, as it slows the freeze cycle.
Will resetting my ice maker erase any settings on my refrigerator?
No. Resetting the ice maker only restarts that one component. Your refrigerator temperature settings, water filter status, and any other preferences remain unchanged. The reset only clears the ice maker's cycle timer and error codes.
What if my GE Profile ice maker has no reset button and no menu option?
Some older GE models reset by turning off the ice maker switch for 30 seconds, then turning it back on. Look for a small lever or switch on the ice maker unit labeled "On/Off" or "Power." Flip it to off, wait 30 seconds, then flip it back to on. If you cannot find a switch or menu option, contact GE support with your model number.
Can I reset the ice maker while it is in the middle of a cycle?
Yes, you can reset at any time. The reset will interrupt the current cycle, drain the mold, and start a new one. This is safe and will not damage the ice maker.
My ice maker reset but still produces no ice. What should I do?
Check the freezer temperature, water supply line, and ice maker power switch again. If all three are correct and the ice maker cycles but produces no ice, the problem is likely a frozen fill tube, a broken solenoid valve, or a sensor failure. These require a technician to repair.