Pairing Your Xfinity Remote to Samsung TV
You can pair most Xfinity remotes to a Samsung TV using the TV's built-in pairing mode, which takes about two minutes. The remote communicates with your TV using infrared (IR) signals, so it does not need a separate app or internet connection — just a clear line of sight between the remote and the TV's sensor.
The exact steps depend on which Xfinity remote model you have. The most common models are the Xfinity XR11 (voice remote with a microphone button) and the XR15 (larger voice remote). Both pair the same way, but older remotes like the XR2 may require a different approach. Check the model number on the back of your remote before you start.
Key Takeaways
- Most Xfinity remotes pair to Samsung TVs by holding the Xfinity and Info buttons together for three to five seconds until the light blinks.
- Your Samsung TV must be powered on and you must point the remote directly at the TV's sensor during pairing.
- If pairing fails, restart both the remote and TV, then try again with fresh batteries in the remote.
- Once paired, the remote controls volume and power on your Samsung TV without any additional setup.
Pairing an XR11 or XR15 Remote to Your Samsung TV
Turn on your Samsung TV and make sure it is in a normal viewing state — not in a menu or setup screen. Point the Xfinity remote directly at the TV's sensor (usually a small dark window on the front or bottom of the TV). Hold the remote about 12 inches away from the TV.
Press and hold the Xfinity button and the Info button at the same time. Keep both buttons pressed for three to five seconds. You will see the LED light on the remote blink amber or red, then turn solid. When the light stops blinking and stays on, release both buttons. Your remote is now paired to the TV.
Test the pairing by pressing the volume up button on the remote. If the Samsung TV's volume bar appears on screen, the pairing worked. If nothing happens, the remote did not pair — move to the troubleshooting section below.
Pairing an Older Xfinity Remote (XR2 or Earlier)
Older Xfinity remotes use a different pairing method. Turn on your Samsung TV and point the remote at it from about 12 inches away. Press and hold the Setup button (on some models labeled Mode) until the LED light blinks twice, then release.
Enter the code 0060 using the number buttons on the remote. The LED should blink twice to confirm the code was entered. Press the Power button once. If the TV turns off, pairing was successful. Turn the TV back on and test the volume buttons to confirm.
If the TV does not respond, try code 0061 or 0062 instead. Samsung TVs sometimes respond to different codes depending on the model year. Enter the code the same way: hold Setup, type the numbers, then press Power to test.
What to Do If the Remote Will Not Pair
The most common reason pairing fails is weak batteries. Remove the batteries from the back of the remote and replace them with fresh ones. Alkaline batteries work best — avoid rechargeable batteries, which often do not provide enough power for the pairing signal.
Make sure you are pointing the remote directly at the TV's sensor and that nothing is blocking the path between them. Furniture, curtains, or even your hand can block the infrared signal. Try pairing again from a clear angle about 12 inches from the TV.
If pairing still fails, restart both devices. Unplug the Samsung TV from the wall outlet and wait 30 seconds, then plug it back in. While the TV is restarting, remove the batteries from the remote for 10 seconds, then reinsert them. Once both devices are fully powered on, try pairing again using the steps above.
Controlling Your Samsung TV After Pairing
Once the remote is paired, you can use the basic buttons to control your TV: Power turns it on and off, Volume Up and Volume Down adjust the sound, and Channel Up and Channel Down change channels (if you are watching cable through Xfinity). The remote will also control your Xfinity cable box at the same time — both devices respond to the same remote.
If you want to control only the TV and not the cable box, you can reprogram the remote to work with just the Samsung TV. This requires entering a different setup code, but most people find it easier to use one remote for both devices. Check your Xfinity remote manual if you want to split the controls between devices.
The remote does not need to be re-paired unless you replace the remote itself or factory reset your Samsung TV. If you reset the TV, you will need to pair the remote again using the same steps.
Using Voice Commands on XR11 and XR15 Remotes
If you have an XR11 or XR15 remote, you can use voice commands to control your TV after pairing. Press the microphone button (usually at the top of the remote) and say a command like "volume up," "mute," or "power off." The remote sends the command to your TV through the same infrared connection.
Voice commands work best for straightforward controls like volume and power. More complex commands like "show me action movies" require the Xfinity cable box and may not work with just the Samsung TV. Stick to basic voice controls if you are using the remote only for the TV.
Frequently Asked Questions
Can I use my Xfinity remote with any Samsung TV?
Most Samsung TVs from the last 15 years work with Xfinity remotes using infrared pairing. Very old Samsung TVs (before 2005) or very new smart TVs with only Bluetooth may not pair. If pairing fails after trying all the codes above, your TV model may not be compatible with Xfinity remotes.
Do I need to pair the remote every time I use it?
No. Once you pair the remote to your Samsung TV, the pairing stays active until you replace the remote or reset the TV. You do not need to re-pair it each time you turn on the TV.
What if I have both an Xfinity cable box and a Samsung TV?
The remote will control both devices at the same time after pairing. Volume and power commands go to the TV, while channel and menu commands go to the cable box. If you want separate control, you can reprogram the remote to work with only one device, though this requires entering additional setup codes.
Can I pair multiple Xfinity remotes to the same Samsung TV?
Yes. Each remote pairs independently using the same steps. If you have two Xfinity remotes in your home, both can control the same TV. The TV does not limit how many remotes can pair to it.
Why does my remote work sometimes but not always?
This usually means the batteries are getting weak. Replace them with fresh alkaline batteries and test again. If the problem continues, check that nothing is blocking the path between the remote and the TV's sensor, and make sure you are pointing the remote directly at the TV rather than at an angle.