Remove the battery by pressing the release tab and sliding the battery pack out
The Ring Doorbell Plus battery slides out from the bottom of the device. You do not need tools or a screwdriver. Press the small release tab on the underside of the doorbell, then slide the battery pack downward and away from the unit. The entire process takes less than a minute.
Before you start, make sure the doorbell is not actively recording or in use. If someone is at your door or the device is processing a video, wait for that action to finish. This prevents data loss and protects the battery contacts from damage during removal.
Key Takeaways
- The battery pack slides out from the bottom of the Ring Doorbell Plus using only your fingers — no tools required.
- You must press the release tab on the underside while sliding the battery downward to remove it safely.
- The battery pack is rechargeable and connects to the doorbell through metal contact points that should stay clean and dry.
- Removing the battery will disconnect the doorbell from power, so any recording or live view will stop when ready.
- You can remove and reinsert the battery as many times as needed without damaging the device or battery.
Locate the release tab on the bottom of the doorbell
Turn the Ring Doorbell Plus over or tilt it so you can see the bottom. You will see a small rectangular tab or notch. This is the release mechanism. It is usually made of plastic and sits flush with the body of the doorbell. The tab is small but straightforward to feel with your finger.
If you are having trouble seeing it, use a flashlight or move to a brighter area. The tab is typically located near the center of the bottom edge, but the exact position can vary slightly depending on the manufacturing batch. Feel along the bottom edge with your thumb if you cannot see it clearly.
Press and hold the release tab while sliding the battery out
Use your thumb or index finger to press the release tab firmly inward. You should feel a slight click or resistance as the tab depresses. While holding the tab down, use your other hand to grasp the battery pack and slide it downward and away from the doorbell body. The battery should slide smoothly without requiring force.
If the battery does not slide easily, stop and check that you are pressing the release tab fully. Do not pull hard or twist the battery, as this can damage the metal contact points. The battery pack should come free with gentle, steady pressure once the tab is fully depressed.
Inspect the battery contacts before reinserting
Once the battery is out, look at the metal contact points on both the battery pack and inside the doorbell. These contacts should be clean, dry, and free of dirt, dust, or corrosion. If you see any discoloration, white powder, or buildup, gently wipe the contacts with a dry cloth or a cotton swab.
Do not use water, cleaning solutions, or abrasive materials on the contacts. Moisture can cause connection problems or battery damage. If the contacts look corroded or damaged, the battery pack may need to be replaced. A poor connection will prevent the doorbell from charging or powering on properly.
Reinsert the battery by aligning and sliding upward
To put the battery back in, hold it so the metal contacts face the doorbell opening. Slide the battery upward into the slot until you hear or feel a click. The click indicates the battery is fully seated and the release tab has locked into place. The battery should sit flush with the doorbell body with no gaps.
Once inserted, the doorbell will power on automatically if it was previously connected to your Ring account. You may see a light indicator or hear a startup sound. If nothing happens, remove the battery again and check that the contacts are clean and properly aligned. Reinsert and try again.
What to do if the battery is stuck or will not come out
If the battery pack is stuck, do not force it. Stop pulling and check that you are pressing the release tab all the way in. Sometimes the tab requires firm, deliberate pressure. Press it again and hold it while you gently wiggle the battery side to side as you slide it downward.
If the battery still will not budge, the release mechanism may be jammed or the battery pack may be swollen. A swollen battery is a safety concern and should not be used. In this case, contact Ring support for a replacement battery. Do not attempt to pry the battery out with tools, as this can damage the doorbell or cause injury.
Frequently Asked Questions
Do I need to turn off the doorbell before removing the battery?
You do not need to turn it off, but the doorbell will lose power when ready when the battery is removed. Any active recording or live view will stop. If someone is at your door, wait for them to leave or for the recording to finish before removing the battery.
Can I damage the doorbell by removing the battery?
No. The battery is designed to be removed and reinserted many times. As long as you use the release tab and do not force the battery, there is no risk of damage to the doorbell or the battery pack.
How often can I remove and reinsert the battery?
You can remove and reinsert the battery as often as you need. There is no limit to how many times you can do this. Each removal and reinsertion does not wear out the battery or the doorbell.
What if the battery pack is swollen or bloated?
A swollen battery should not be used and should not be charged. Stop using it when ready and contact Ring to order a replacement battery pack. Do not attempt to remove a swollen battery by force, as it may leak or rupture.
Will removing the battery erase my video recordings?
No. Your video recordings are stored in the cloud through your Ring account, not on the battery or doorbell. Removing the battery will not delete any videos. Once you reinsert the battery and the doorbell reconnects to power and Wi-Fi, your account and recordings will be intact.