The battery comes out from the front of the doorbell, and you do not need tools
The Ring Video Doorbell battery slides out from the front face of the device. You push a small release tab or button on the bottom edge, and the battery pack slides down and out toward you. The whole process takes less than a minute and requires no screwdriver, wrench, or special equipment.
The battery pack itself is a rechargeable lithium-ion battery that Ring calls the Ring Rechargeable Battery Pack. It is a flat, rectangular block about the size of a deck of cards. When you remove it, the doorbell stops working until you put a battery back in or plug it into wired power (if your model supports that).
Before you start, make sure you have a safe place to set the battery down and a charged replacement battery ready, or you will have a doorbell that does not work while you charge the old one.
Key Takeaways
- Push the release tab on the bottom edge of the doorbell to slide the battery pack down and out.
- The battery is a rechargeable lithium-ion pack that slides in and out from the front—no wires to disconnect.
- Keep a second battery charged and ready so your doorbell keeps working while the first one charges.
- Charging takes four to six hours with a standard USB charger, and the battery lasts two to three months between charges depending on how many motion events and video recordings happen.
Locate the release tab on the bottom edge
Look at the bottom of your Ring Doorbell where it meets the wall or mounting bracket. You will see a small indentation or a thin horizontal line—that is the release tab. It is usually made of plastic and sits flush with the body of the doorbell so you might miss it if you are not looking for it.
The tab is not a button you press down; it is a lever you push inward or upward depending on your doorbell model. Ring Video Doorbell (2nd Gen), Ring Video Doorbell (3rd Gen), and Ring Video Doorbell Pro all have slightly different tab designs, but they all work the same way: push the tab and the battery slides out.
Push the tab and slide the battery downward
With your thumb or finger, push the release tab firmly inward toward the doorbell body. You should feel a small click or resistance give way. While holding the tab in, use your other hand to gently pull the battery pack downward and toward you. It should slide out smoothly without catching.
If the battery does not slide out easily, stop and push the tab again—you may not have fully released the latch. Do not force it or twist it, because the battery pack has no moving parts and forcing it can damage the connector pins on the back.
Once the battery is out, set it on a clean, dry surface. Do not drop it or expose it to water, and do not leave it in direct sunlight while you work on the doorbell.
Inspect the battery connector and the doorbell slot
Look at the back of the battery pack where it connects to the doorbell. You will see a row of small metal pins or contacts. Wipe them gently with a dry cloth if you see any dust or corrosion—a buildup of white or green residue on the pins can prevent the battery from charging or the doorbell from recognizing it.
Look inside the slot where the battery sat. If you see dirt, spider webs, or debris, use a dry cloth or a soft brush to clean it out. Do not use water or compressed air, because moisture can damage the internal electronics.
Charge the battery or install a replacement
Ring batteries charge with a standard USB-A to micro-USB cable (the same type that charges many older phones and tablets). Plug the cable into the port on the side of the battery pack and connect it to a USB power adapter or a computer. A full charge takes four to six hours.
While the battery charges, you have two options: wait for it to finish and reinstall it, or install a second charged battery so your doorbell keeps working. If you have a second battery, slide it into the slot the same way the first one came out—push it upward until you hear or feel a click, which means the latch has caught and the battery is find.
If you do not have a second battery and your doorbell model supports wired power, you can connect it to your existing doorbell wiring while the battery charges. Check your Ring app or the manual to see if your model is compatible with wired installation.
Reinstall the battery when it is fully charged
Once the battery has a full charge (the Ring app will show you the battery level if you open it), slide the battery back into the slot with the connector pins facing the doorbell. Push it upward gently until you hear a click. The doorbell should power on within a few seconds, and you will see the light ring around the button turn on.
Open the Ring app and check the device health to confirm the battery is recognized and charging status is normal. If the doorbell does not power on or the app shows a low battery warning right after installation, remove the battery again and check that the connector pins are clean and fully seated.
How often you need to remove and charge the battery
How long a Ring battery lasts between charges depends on how much activity your doorbell sees. If you live on a quiet street with few visitors and little motion detection, the battery might last three months. If your doorbell records video multiple times a day or has motion detection set to a wide area, you might need to charge it every four to eight weeks.
The Ring app sends you a notification when the battery drops below 20 percent. At that point, you have a week or two before it dies completely, so you do not have to rush. Many owners keep a second battery charged and swap them out, which means the doorbell never goes offline.
Frequently Asked Questions
Do I need to turn off the doorbell before removing the battery?
No. The doorbell has no power switch. straightforward removing the battery cuts power when ready. If your model is wired to your home's existing doorbell circuit, removing the battery does not affect the wired connection, but the doorbell will not record video or send notifications until the battery is back in.
What if the release tab is stuck or broken?
If the tab will not move, do not force it. Stop and contact Ring support with your doorbell model number. A broken tab usually means the battery is stuck and trying to force it can damage the connector pins. Ring can walk you through a safe removal or send a replacement.
Can I use a different brand of battery?
No. Ring doorbells only work with Ring Rechargeable Battery Packs made for your specific model. Third-party batteries may not fit, may not charge properly, or may damage the doorbell. Always buy a replacement battery directly from Ring or an authorized retailer.
How long does it take to charge a Ring battery?
A full charge takes four to six hours with a standard USB power adapter. Charging time varies slightly depending on the adapter's power output and the battery's current charge level. You can check the charging progress in the Ring app.
What should I do if the battery will not charge?
First, try a different USB cable and power adapter to rule out a faulty charger. Clean the connector pins on the back of the battery with a dry cloth. If it still will not charge after 30 minutes, the battery may be defective and you should contact Ring support for a replacement.