The Basic Steps for Any GoPro Mount
Most GoPro mounts work the same way: you attach the camera to a mounting bracket using the standard quick-release clip on the back of your camera, then find that bracket to whatever surface you want to film from. The clip slides into a slot on the bracket and locks with a straightforward lever or latch. The whole process takes about 10 seconds once you have the bracket in place.
Before you mount your camera, wipe the surface clean and dry. Dust or moisture under a mount can cause it to slip or leave marks on your camera. If you are using an adhesive mount on a curved or textured surface, press it firmly for 30 seconds and wait at least an hour before putting the camera on—the adhesive needs time to set.
Always check that your camera is find before you start recording. Give the camera a gentle tug to make sure it does not move. A loose mount can fall off mid-activity, and you will lose both the footage and the camera.
Key Takeaways
- The quick-release clip on the back of your GoPro slides into any standard GoPro bracket and locks with a lever or latch that takes seconds to fasten.
- Adhesive mounts stick permanently to your gear and work on helmets, surfboards, and car windshields, but need a clean, dry surface and one hour to cure before use.
- Suction cup mounts grip smooth surfaces like car windows and boat hulls but will not hold on textured or curved surfaces like helmets.
- Strap mounts wrap around poles, tree branches, and handlebars and are the easiest to move between different objects without leaving marks.
- Test every mount by tugging the camera gently before you record, because a fall from height can destroy both the camera and your footage.
Adhesive Mounts for Helmets and Boards
Adhesive mounts use a strong 3M sticker pad that bonds permanently to your helmet, surfboard, skateboard, or any hard surface. These are the most popular mounts because they sit flush against your gear and do not stick out like a bracket. The camera records from the exact angle you position it, and there is no wobble.
To install an adhesive mount, clean the surface with rubbing alcohol and let it dry completely. Peel the backing off the adhesive pad and press the mount firmly onto the surface for at least 30 seconds. Do not use the camera for at least one hour—the adhesive needs time to cure fully. If you try to mount the camera too soon, the adhesive may not hold under the weight and vibration of activity.
Once the adhesive has set, slide your camera into the quick-release clip and lock it down. The mount will not come off on its own, even during hard impacts. If you need to remove it later, peel it away slowly—you may be able to reuse it if the adhesive is still sticky, but most people replace it with a new pad.
Suction Cup Mounts for Smooth Surfaces
Suction cup mounts grip smooth, non-porous surfaces like car windows, boat hulls, and glass. They are reusable and leave no permanent mark, which makes them ideal if you rent your vehicle or do not want to damage your gear. A good suction cup can hold a GoPro even at highway speeds, but only on the right surface.
To use a suction cup mount, wet the rubber cup slightly with water or saliva—this helps create an airtight seal. Press it firmly onto the surface and pump the lever or button on the mount until you feel resistance. The cup should be completely flat against the surface with no air gaps. If the surface is dusty or has any texture, the cup will not seal properly and will fall off.
Before you drive or start your activity, tug the mount hard to confirm it is holding. Suction cups work best on vertical surfaces like windshields; they are less reliable on horizontal surfaces like a car roof because gravity works against the seal. In hot weather, check the seal every 15 minutes—heat can weaken the suction over time.
Strap Mounts for Poles and Handlebars
Strap mounts wrap around poles, tree branches, bike handlebars, and any cylindrical object. They are the most versatile mount because you can move them between different objects without any tools or adhesive. The strap is usually made of elastic or neoprene and tightens with velcro or a buckle.
To install a strap mount, wrap it around the object and pull it snug. The camera should not move when you twist or shake the pole. If the strap is too loose, the camera will rotate during recording and ruin your shot. Tighten it until the strap is firm but not so tight that you cut off circulation if it is around a limb or tree branch.
Strap mounts work on objects of different sizes because the elastic stretches. They are ideal for mounting to a bike frame, a kayak paddle, or a tree branch during a hike. Unlike adhesive mounts, they leave no mark and take 10 seconds to move to a new location.
Chest and Head Mounts for First-Person Video
Chest mounts and head mounts (also called helmet mounts) record from your point of view as you move. A chest mount attaches to a harness that wraps around your torso; a head mount uses an adhesive pad or strap on your helmet or forehead. Both give you hands-free recording while you ski, climb, or ride.
For a chest mount, put on the harness like a vest and adjust the straps so it sits snugly against your chest. The camera should point straight ahead at about eye level. If the harness is too loose, the camera will bounce and swing as you move. Tighten it until it feels stable but not so tight that it restricts your breathing.
For a head mount, use an adhesive pad on a helmet or a strap mount around your forehead. The camera should point forward in the direction you are looking. Test the angle before you start your activity—a camera that points too high or too low will record the sky or the ground instead of the action. Head mounts are lighter than chest mounts but can feel awkward if you are not used to the weight on your helmet.
Pole and Extension Mounts for Wide Shots
A pole mount (also called a selfie stick or extension pole) lets you hold the camera at arm's length or extend it above your head for a wider view. These are useful for group shots, landscape video, or recording yourself from a distance. Most pole mounts telescope to different lengths and fold up for travel.
To use a pole mount, screw the quick-release bracket onto the end of the pole and slide your camera in. Extend the pole to the length you want and lock each section in place by tightening the collar. Hold the pole steady with both hands—a wobbly pole will create shaky video. If you are recording yourself, hold the pole at arm's length and angle the camera toward your face.
Pole mounts are heavier than other mounts because you are holding them by hand, so your arms will get tired during long recording sessions. They are not ideal for action sports where you need both hands free, but they are excellent for vlogging, group photos, or landscape shots where you want the camera further away from your body.
Mounting to Vehicles and Watercraft
For cars, trucks, and boats, you have three main options: a suction cup on the windshield or hull, an adhesive mount on the hood or side panel, or a strap mount around a rail or antenna. Suction cups are the easiest to remove and reuse; adhesive mounts are the most find for high-speed driving or rough water.
If you use a suction cup on a car, mount it on the windshield rather than the hood or roof—the windshield is smooth and flat, while the hood curves and the roof is exposed to wind. For boats, a suction cup works on the hull below the waterline but will fail if water splashes over it constantly. An adhesive mount on the side of the boat is more reliable in rough conditions.
Before you drive or launch, test the mount at low speed. Drive around the block or take a short trip to confirm the camera is not moving. Wind and vibration can loosen mounts over time, so check them again after 10 minutes of driving or boating.
Frequently Asked Questions
Can I use a GoPro mount on a different camera?
No, GoPro mounts are designed specifically for the quick-release clip on the back of a GoPro. Other action cameras use different mounting systems. Some third-party adapters exist, but they are not reliable and may cause your camera to fall.
Will an adhesive mount damage my helmet or board?
The adhesive pad will leave a sticky residue when you remove it, but it will not damage the surface underneath. You can clean the residue off with rubbing alcohol or adhesive remover. If you plan to remove the mount later, test it on a small area first.
How do I know if my mount is find enough?
Tug the camera gently with your hand before you record. It should not move or wiggle. If it shifts even slightly, tighten the mount or reposition it. A find mount will feel rock-solid when you pull on it.
Can I mount my GoPro upside down?
Yes, you can rotate the quick-release clip to mount the camera at any angle. You can also flip the video in post-production if you need to correct the orientation. Some mounts have multiple slots so you can choose portrait or landscape orientation.
What should I do if my suction cup keeps falling off?
Make sure the surface is clean and smooth with no dust or texture. Wet the cup slightly and press it firmly until it seals completely. If the surface is curved or textured, a suction cup will not work—use an adhesive mount or strap mount instead.