Press and hold the power button on the side of the camera
The power button on a GoPro Hero is a small circular button on the side of the camera body, usually near the bottom. Press and hold it for about three seconds until you see the GoPro logo appear on the screen and hear a startup sound. The camera will then boot up and show you the home menu.
If the camera does not respond, the battery may be empty. Plug the camera into a USB charger using the cable that came in the box, or insert a fully charged battery if you have a spare. GoPro batteries typically take two to three hours to charge fully from empty.
Once the camera is on, the screen will display the main menu with options like Record, Photos, and Settings. You are now ready to use the camera.
Key Takeaways
- The power button is a small circular button on the side of the camera body; press and hold it for three seconds to turn on the camera.
- The camera will show the GoPro logo and play a startup sound when it powers on successfully.
- If the camera does not turn on, the battery is likely empty and needs to be charged for two to three hours.
- Once powered on, the home menu appears on the screen and the camera is ready to record or take photos.
What to do if the camera won't turn on
If you press the power button and nothing happens, the battery is almost certainly dead. Connect the camera to power using the USB-C cable (on newer Hero models) or the micro-USB cable (on older models) that came with your camera. Plug the other end into a wall charger, a computer, or a portable power bank. You should see a charging indicator on the screen within a few seconds.
If you see a charging indicator but the camera still will not turn on after 30 minutes of charging, try a different USB cable or charger. Sometimes the cable itself is damaged. If the camera has been sitting unused for several months, it may take 10 to 15 minutes of charging before it has enough power to boot up.
Understanding the startup screen and menu
When the camera first powers on, you will see the GoPro logo for a few seconds, then the home menu. The home menu shows you the main recording modes: Record (video), Photos (still images), and Burst (multiple photos in quick succession). Below these are Settings, where you can adjust resolution, frame rate, and other options.
The screen may also show battery percentage in the top corner and the current recording mode highlighted in the center. If this is your first time using the camera, the menu may prompt you to connect to the GoPro app or set the date and time. You can skip these steps and start recording right away if you prefer.
Turning the camera off
To turn off the camera, press and hold the power button again for three seconds. The screen will go black and you will hear a shutdown sound. The camera is now off and will not drain the battery while sitting unused.
If you leave the camera on without recording, it will stay powered on until you manually turn it off. Some newer Hero models have an auto-off feature that you can enable in Settings, which will shut down the camera after a set time of inactivity (usually 5 or 10 minutes).
Charging and battery care
GoPro Hero cameras use rechargeable lithium batteries that come partially charged from the factory. Before your first use, charge the battery fully using the USB cable and a wall charger. A full charge typically takes two to three hours depending on the model and charger type.
To extend battery life, avoid leaving the camera powered on when you are not using it. Cold temperatures drain batteries faster, so if you are filming in winter or at high altitude, bring a spare battery and keep it warm in an inside pocket. You can also purchase additional batteries separately and swap them out when one runs low.
Troubleshooting common startup issues
If the camera turns on but the screen is black or frozen, try holding the power button for 10 seconds to force a restart. This will shut down the camera completely and then turn it back on, which often clears temporary glitches.
If the camera turns on but shows a low battery warning when ready, charge it for at least 30 minutes before recording. Recording video drains the battery faster than the camera can charge it, so you may not be able to record while plugged in if the battery is very low.
If you see an error message on the screen, write down the exact message and check the GoPro support website or your camera's manual. Most error messages relate to the SD card, battery, or a software issue that can be fixed by restarting or updating the camera firmware.
Using the camera right after turning it on
Once the camera is on and you see the home menu, you can start recording when ready by pressing the shutter button (the large button on top of the camera). The camera will begin recording video in whatever mode and resolution you last used. If you want to change settings first, navigate to Settings using the menu buttons and adjust resolution, frame rate, or other options before you start recording.
The camera will record continuously until you press the shutter button again to stop. Video files are saved to the SD card inside the camera, so make sure an SD card is inserted before you start recording. If no SD card is present, the camera will show a warning and will not record.
Frequently Asked Questions
How long does it take for a GoPro Hero to turn on?
The camera usually boots up within 5 to 10 seconds of pressing the power button. You will see the GoPro logo appear on the screen first, then the home menu. If it takes longer than 15 seconds, the battery may be low or there may be a software issue.
Can I turn on the camera using the GoPro app instead of the power button?
No, you must use the physical power button on the camera to turn it on. Once the camera is powered on, you can control it remotely using the GoPro app over Wi-Fi, but the app cannot power on a camera that is completely off.
What does it mean if the camera powers on but the screen stays black?
A black screen usually means the camera is on but the display is not working, or the camera is in a mode where the screen is turned off to save battery. Try pressing the power button for 10 seconds to restart the camera. If the screen remains black, the display may need repair.
Does the camera drain battery when it is turned off?
No, a powered-off camera uses almost no battery. You can leave it off for weeks or months without the battery draining. However, lithium batteries do lose charge slowly over time even when not in use, so charge the camera every few months if you store it for long periods.
Why does my camera turn on but when ready show a low battery warning?
The battery is nearly empty and needs to be charged. Plug the camera in and let it charge for at least 30 minutes before recording. If the battery drains very quickly even after a full charge, the battery may be worn out and may need to be replaced.