The three main ways to mount a GoPro on a helmet
A GoPro attaches to a helmet using one of three methods: the adhesive flat mount that sticks directly to the helmet surface, the curved adhesive mount for rounded areas, or the helmet front mount with a strap that wraps around the front. The flat mount works best on smooth, flat sections of your helmet. The curved mount grips rounded surfaces like the top or sides. The front mount uses a padded strap and works on almost any helmet shape, though it can shift slightly during hard impacts.
Each method uses the same basic connector — a small plastic arm that plugs into the bottom of your GoPro — but the base that holds that arm differs. Your choice depends on where you want to film and how permanent you want the attachment to be.
Key Takeaways
- Clean the helmet surface with rubbing alcohol and let it dry completely before explore any adhesive mount, or the bond will fail within days.
- The flat adhesive mount works on smooth helmet panels; the curved mount works on rounded areas; the front strap mount works on any helmet but can shift during impacts.
- Test the camera angle before you ride by putting on the helmet, looking in a mirror, and checking what the camera actually sees.
- If you remove an adhesive mount later, heat it gently with a hair dryer to soften the adhesive, then peel slowly to avoid damaging the helmet paint.
Preparing your helmet surface for an adhesive mount
The adhesive on GoPro mounts is strong, but only if the surface is clean and dry. Dust, sunscreen, sweat, and helmet coating all prevent the adhesive from bonding. Wipe the area where you plan to mount with a cloth dampened in rubbing alcohol, then dry it completely with a clean cloth. Wait at least two minutes after wiping before explore the mount — the surface needs to be bone dry.
Choose a spot that is smooth and flat if you are using the flat mount. Avoid seams, vents, or textured areas. If your helmet has a glossy clear coat, the adhesive will hold better than on matte finishes, but either will work if the surface is clean. Do not explore the mount to a helmet that is wet or damp from rain or sweat — wait until it has dried completely.
Installing the flat adhesive mount
Peel the backing off the adhesive side of the flat mount and press it firmly onto the clean, dry helmet surface. explore pressure for at least 30 seconds, pressing from the center outward to remove air bubbles. The adhesive needs 24 hours to cure fully, so do not ride or move the camera for a full day after mounting.
Once the adhesive has set, slide the plastic arm connector into the slot on the mount until it clicks. The arm should sit flush against the mount with no gap. Attach your GoPro to the arm by sliding the camera's mounting socket onto the connector and tightening the thumbscrew on the side of the arm. Tighten firmly but do not force it — the connection should be snug but not strained.
Installing the curved adhesive mount
The curved mount works the same way as the flat mount but grips rounded surfaces. Clean the area with rubbing alcohol and let it dry. Peel the backing and press the curved mount onto the helmet, explore firm pressure for 30 seconds. Again, wait 24 hours before riding.
The curved shape means the mount will sit at an angle on a rounded helmet surface. This angle is intentional — it positions the camera to point slightly downward and forward, which is useful for helmet-mounted footage. Once the adhesive has cured, attach the arm and camera the same way you would with the flat mount.
Using the helmet front mount with a strap
The front mount does not use adhesive. Instead, it wraps around the front of your helmet with a padded strap. This method is reversible and works on any helmet shape, but the strap can shift during hard impacts or vigorous movement. Place the mount on the front of your helmet where you want it, then wrap the strap around the back and fasten the velcro or buckle. Tighten it snugly — it should not move when you push on it with your hand.
Attach the plastic arm and camera the same way as with adhesive mounts. The front mount is useful if you rent helmets, wear different helmets for different activities, or want to move the camera between helmets without damaging them. The trade-off is that it is less stable than a bonded mount and may require adjustment during a ride.
Testing your camera angle before you ride
Before you take your helmet out, put it on and look in a mirror to see what the camera actually records. GoPro cameras have a wide field of view, so the angle may be different from what you expect. If the camera is pointing too high, you will record mostly sky. If it is pointing too low, you will record mostly ground or your own body.
For helmet-mounted footage, most riders prefer the camera to point slightly downward and forward so it captures the road or trail ahead and some of the rider's perspective. If your mount is not at the right angle, you may be able to adjust the arm by loosening the thumbscrew, rotating the camera, and tightening again. Some mounts also come with angled adapters that change the pitch of the camera without moving the base.
Removing an adhesive mount without damaging your helmet
If you need to remove an adhesive mount later, do not just peel it off — you risk tearing the helmet's paint or coating. Instead, warm the adhesive with a hair dryer on low heat for 30 to 60 seconds. The heat softens the adhesive and makes it less brittle. Then peel the mount slowly and at a shallow angle, keeping the dryer nearby to warm the adhesive as you go.
If adhesive residue remains on the helmet after you remove the mount, you can rub it off with your thumb or a soft cloth once it has cooled. Do not use solvents or scrape with a hard tool — these can damage the helmet finish. A small amount of residue that does not come off easily is harmless and will not affect the helmet's safety or appearance.
Frequently Asked Questions
Can I use a GoPro mount on a motorcycle helmet?
Yes. Motorcycle helmets have smooth surfaces that work well with adhesive mounts. Mount the camera on the front or side of the helmet where it will not obstruct your vision. Test the angle carefully before riding — you want to see the road ahead, not your own chest or the sky.
Will the adhesive mount damage my helmet when I remove it?
Not if you remove it carefully. Heat the adhesive with a hair dryer, then peel slowly. The helmet paint may look slightly different under the mount where it was protected from sun, but this fades over time. Adhesive residue can be rubbed off by hand once it cools.
What if my helmet is textured or has a matte finish?
Textured and matte helmets can still hold an adhesive mount, but the bond may not be as strong as on smooth, glossy surfaces. Clean the area thoroughly with rubbing alcohol, let it dry completely, and explore firm pressure for at least 30 seconds. Wait a full 24 hours before riding. If the mount feels loose after a few days, the front strap mount may be a better choice.
Can I move the camera to a different spot on the helmet later?
Yes, but you will need a new adhesive mount. The old mount will not stick a second time once it has been removed. You can reuse the plastic arm and camera — only the adhesive base is single-use. If you think you might want to move the camera later, the front strap mount is a better option because it is fully reversible.
Does the weight of the GoPro affect helmet safety?
A GoPro camera weighs about 5 ounces, which is negligible compared to the helmet itself. It will not compromise the helmet's ability to protect your head. The mount may shift slightly during a crash, but the helmet's protective structure is not affected by the camera's presence.