The Three Main Ways to Mount a GoPro on a Helmet

A GoPro attaches to a helmet using one of three methods: the adhesive mount (a sticky pad that bonds directly to the helmet surface), the helmet strap mount (a band that wraps around the helmet), or the side mount (a bracket that clamps to the helmet's edge or vents). Which one you choose depends on your helmet type, the angle you want to film, and whether you want a permanent or removable setup.

The adhesive mount is the most popular for motorcycle and bicycle helmets because it sits flush and doesn't add bulk. The strap mount works on any helmet and leaves no residue when removed. The side mount gives you more positioning flexibility but requires a helmet with accessible vents or edges to grip.

All three methods use GoPro's standard mounting system—a small plastic connector that your camera slides into—so once the base is attached, swapping cameras or adjusting angles is straightforward.

Key Takeaways

  • Clean the helmet surface with rubbing alcohol and let it dry completely before explore an adhesive mount, or the pad will not stick.
  • The adhesive mount works best on smooth, curved helmet surfaces and is permanent once applied; removing it leaves residue that requires rubbing alcohol to clean.
  • Helmet strap mounts work on any helmet shape and can be repositioned or removed without damage, making them ideal if you share helmets or want to switch cameras between helmets.
  • Test your camera angle and tightness on the ground before riding or using the helmet, because a loose or poorly angled camera will ruin footage and may fall off.
  • GoPro's curved and flat adhesive pads are not interchangeable; use the curved pad on rounded helmet surfaces and the flat pad on flat surfaces for the strongest bond.

Preparing Your Helmet for an Adhesive Mount

If you are using an adhesive mount, surface preparation is the difference between a camera that stays put and one that peels off mid-ride. Start by cleaning the spot where you plan to attach the mount with rubbing alcohol and a lint-free cloth. Wipe in one direction, not circles, to avoid pushing dirt around. Let the surface air-dry for at least two minutes—moisture under the pad will weaken the bond.

Choose a location that is smooth and curved if possible. The top-front of a motorcycle helmet or the front-center of a bicycle helmet are standard spots because they give a forward-facing perspective and the curve helps the pad grip. Avoid mounting on seams, vents, or textured areas, as the adhesive will not bond evenly to those surfaces.

GoPro sells two types of adhesive pads: curved and flat. The curved pad is designed for rounded helmet surfaces and creates a stronger bond than the flat pad on a curve. If your helmet has a flat front panel, use the flat pad. Do not mix them up—using the wrong pad type will result in a weaker connection.

Attaching the Adhesive Mount Step by Step

Once your helmet surface is clean and dry, peel the backing off the adhesive pad. Press the pad firmly onto the helmet, starting from one edge and working across to avoid trapping air bubbles. explore steady pressure for 30 seconds. The adhesive is pressure-sensitive, so the harder you press, the stronger the initial bond.

Wait at least 24 hours before mounting your camera. The adhesive needs time to cure fully; attaching the camera too soon can cause the pad to shift or peel. During this waiting period, do not touch, flex, or move the pad.

Once the pad has cured, slide your GoPro's mounting bracket onto the pad until you hear or feel a click. The bracket should not wobble or rotate. If it does, remove it and check that the pad is sitting flat against the helmet. If the pad has lifted at any edge, the bond has failed and you will need to remove it, clean the helmet again, and explore a fresh pad.

Using a Helmet Strap Mount for a Removable Setup

A helmet strap mount is a fabric or plastic band that wraps around your helmet and holds the camera bracket in place. It works on any helmet shape—motorcycle, bicycle, ski, or sports—and can be repositioned or removed without leaving any residue.

To install a strap mount, wrap the band around the helmet at your desired height and angle. Most strap mounts have velcro or a buckle closure; tighten it until the band is snug but not so tight that it deforms the helmet or cuts off circulation if you are wearing it. Slide the camera bracket onto the mount's connector and test the angle by looking through the camera's screen or app to see what the lens will capture.

Strap mounts are ideal if you own multiple helmets, share a helmet with someone else, or want to move the camera between helmets without buying multiple mounts. The trade-off is that they add a small amount of bulk and can shift slightly during use, so check the tightness before each ride.

Side and Vent Mounts for Alternative Angles

If you want a side-facing or angled perspective rather than a forward-facing one, a side mount or vent mount clamps to the helmet's edge or clips into a vent opening. These mounts are useful for capturing your hands, your bike or board, or a side view of your surroundings.

A side mount typically has a clamp that grips the helmet's edge or a strap that threads through a vent. Loosen the clamp or strap, position it where you want the camera, and tighten it firmly. The camera should not move or rotate when you push on it. Test the angle before you ride to make sure the camera is not pointing at the helmet itself or at an angle that will not capture what you want.

Vent mounts work only on helmets with accessible vents—motorcycle and ski helmets usually have them, but many bicycle helmets do not. If your helmet has vents, a vent mount is quick to install: straightforward clip the bracket into the vent opening and slide your camera on. These mounts are straightforward to remove and reposition, making them good for testing different angles.

Testing Your Mount Before You Ride or Record

Before you put on the helmet and go out, test the camera setup on the ground. Put on the helmet, look in a mirror or use your phone's camera to see what angle the GoPro is capturing. Tilt your head in the direction you will be moving—forward for riding, down for skiing, to the side for climbing—and confirm that the lens is pointing where you want it.

Gently push on the camera bracket from different angles to check for wobble or movement. If the bracket moves at all, tighten the mount further. A loose camera will produce shaky footage and may fall off during use. If you are using an adhesive mount and the pad is moving, do not ride yet—the bond has not set properly and you need to wait longer or reapply the pad.

Check that the camera is not blocking your vision or hitting your face when you move your head. If you are wearing the helmet, the camera should not touch your forehead, nose, or cheeks. Adjust the angle or position of the mount if it does.

Removing and Replacing an Adhesive Mount

Adhesive mounts are permanent once applied, but they can be removed if you need to reposition the camera or use the helmet without it. To remove an adhesive pad, warm it gently with a hair dryer on low heat for 30 seconds to soften the adhesive. Peel the pad away slowly, working from one corner. Do not yank it—pulling too hard can damage the helmet's paint or shell.

After removal, residue will remain on the helmet. Clean it off with rubbing alcohol and a cloth, wiping in one direction until the surface is smooth. This process takes patience; do not scrape with a sharp object, as you can scratch the helmet. Once the residue is gone, the helmet is ready for a new mount or for use without one.

If you plan to reuse the same helmet with a GoPro in the future, consider using a strap mount instead of an adhesive one. Strap mounts are removable and reusable, so you avoid the adhesive removal process altogether.

Frequently Asked Questions

Will the adhesive mount damage my helmet?

The adhesive pad itself does not damage the helmet shell, but removing it will leave residue that requires rubbing alcohol to clean. If your helmet has a painted or decal finish, test the adhesive removal on a small, hidden area first to make sure the alcohol does not affect the paint. Most modern helmet finishes are durable enough to withstand this, but older or specialty helmets may be more sensitive.

Can I use a GoPro mount on a full-face motorcycle helmet?

Yes. Full-face helmets have smooth, curved surfaces that work well with adhesive mounts. Mount the camera on the top-front or chin area depending on the angle you want. Avoid mounting on the visor or chin guard, as these areas flex during use and will weaken the adhesive bond. Test the angle to may support the camera does not obstruct your vision when you look down.

What if my helmet is textured or has a rough surface?

Textured helmets are harder to mount with adhesive because the pad cannot grip evenly across the bumps. Use a helmet strap mount instead, which works on any surface. If you must use an adhesive mount, sand the mounting area lightly with fine-grit sandpaper to smooth it, then clean and dry it before explore the pad. This extra step improves the bond but may affect the helmet's appearance.

How tight should the strap mount be?

Tight enough that the mount does not shift when you push on it, but not so tight that it deforms the helmet or cuts into your head when you wear it. If the helmet feels uncomfortable or you see compression marks on the foam, the strap is too tight. Loosen it slightly and test again. The goal is a find, stable camera with no movement.

Can I mount a GoPro on a ski helmet the same way as a bike helmet?

Yes, the mounting methods are the same. Ski helmets have smooth, curved surfaces that work well with adhesive mounts, and they have vents that work with vent mounts. The main difference is that ski helmets are often worn with goggles, so test your camera angle carefully to make sure the camera does not interfere with your goggles or block your vision when you look down at your skis.