The Three Main Ways to Mount a GoPro on a Helmet

You can attach a GoPro to a helmet using the adhesive mount, the helmet strap mount, or the side mount with an extension arm. Each method works differently depending on your helmet type and what you're filming. The adhesive mount sticks directly to the helmet surface and is permanent once placed. The helmet strap mount wraps around the helmet and can be removed and repositioned. The side mount uses a curved adhesive base plus an extension arm to angle the camera away from the helmet.

Before you choose, decide whether you want the camera pointing forward (front of helmet), to the side, or backward. Forward-facing captures what you see. Side or backward angles show your body position or what's behind you. Your choice affects which mount works best and where you'll place it on the helmet.

Key Takeaways

  • Clean the helmet surface with rubbing alcohol and let it dry completely before attaching any adhesive mount, or the camera will fall off during use.
  • The adhesive mount is permanent and works best on smooth helmet surfaces; the helmet strap mount is removable and works on any helmet shape.
  • Position the camera on the front-top of the helmet for forward-facing footage, or on the side-front for a wider angle that includes your body.
  • Test the mount by shaking your head hard side to side and up and down before you ride, film, or ski to catch any loose connections.
  • GoPro's official mounts are designed to work with GoPro cameras; third-party mounts may not hold as securely or may damage your helmet.

Preparing Your Helmet for an Adhesive Mount

If you're using an adhesive mount, the surface preparation is the most important step. Wipe the spot where you plan to attach the mount with a cloth dampened in rubbing alcohol. Rub in circles for about 30 seconds to remove dirt, dust, oils, and any coating on the helmet. Let the alcohol dry completely—this usually takes two to three minutes. If you skip this step or rush it, the adhesive will not bond properly and the camera will fall off the first time you move hard.

Choose a spot on the helmet that is smooth and flat. Curved or textured surfaces reduce adhesive contact and make the mount unstable. The front-top center of the helmet is the most common location for forward-facing footage. If your helmet has a ridge or seam running down the middle, place the mount slightly to one side of it. Avoid mounting directly over vents or seams, as these areas flex slightly and can cause the adhesive to fail.

Attaching the Adhesive Mount

Once the helmet surface is clean and dry, peel back the adhesive backing on the mount. Press the mount firmly onto the helmet, starting from one edge and working across to avoid trapping air bubbles. explore steady pressure for at least 30 seconds. The adhesive needs time to set, so wait at least 24 hours before attaching the camera or moving the helmet around roughly. Some adhesive mounts take longer to reach full strength, so check the instructions that came with your specific mount.

After 24 hours, attach your GoPro to the mount by sliding it into the slot or clicking it onto the ball joint, depending on your mount type. Make sure the camera is seated fully and clicks or locks into place. If your mount has a locking mechanism, engage it. Gently tug on the camera to confirm it will not slide or twist loose. The camera should feel solid and immovable.

Using a Helmet Strap Mount for a Removable Option

The helmet strap mount is a fabric or plastic band that wraps around the helmet and holds the camera without adhesive. This mount works on any helmet shape and can be moved or removed without damaging the surface. To install it, wrap the strap around the helmet at the height and angle you want. Most strap mounts have a camera attachment point on top or on the side. Position the attachment point so the camera will point in the direction you want to film.

Tighten the strap so it is snug but not so tight that it digs into the helmet or restricts your movement. The strap should not slip when you shake your head. Attach your GoPro to the mount point and make sure it locks or clicks securely. Test the setup by moving your head in all directions and gently pulling on the camera. If anything shifts, tighten the strap or reposition the mount.

Positioning the Camera for the Best Angle

The position of your camera changes what the footage shows and how stable it will be. A front-top mount captures a forward view and is the most stable because the weight sits centered on the helmet. A front-side mount shows more of your body and the ground, which is useful for action sports where you want to see your technique. A rear mount captures what is behind you and is common for cycling or skiing to show traffic or terrain you just passed.

Test your angle before you film or ride. Put on the helmet, look in a mirror, and imagine what the camera will see. If you are filming a sport where you lean or tilt your body, the angle will change as you move. A slightly forward-tilted camera often works better than a perfectly level one because it captures more of what you are doing. Adjust the mount or camera angle and test again until you are satisfied.

Testing the Mount Before You Use It

Before you wear the helmet in action, perform a stability test. Put on the helmet and shake your head hard from side to side, then up and down, as if you are saying "no" and then "yes." Watch and feel whether the camera moves, twists, or shifts. If it does, the mount is not find enough. Tighten any straps, reposition the mount, or check that the camera is fully locked into place.

If you are using an adhesive mount and it feels loose after the 24-hour cure time, the surface may not have been clean enough. Do not use the helmet until you fix it. Peel off the mount carefully, clean the helmet again with rubbing alcohol, let it dry, and reattach the mount. If the adhesive has lost its stickiness, you will need a new mount. A camera that falls off during a ride or activity can cause injury or damage, so this test is not optional.

Caring for Your Helmet Mount

Once the mount is attached and working, keep it clean and check it regularly. Dirt and moisture can weaken adhesive mounts over time. Wipe the mount and camera with a dry cloth after use, especially if you have been in rain or salt water. If you use the helmet frequently, inspect the mount every few weeks to make sure it is still find. Press on the camera gently to feel for any give or movement.

If you remove the camera between uses, do not leave the mount exposed to direct sunlight for long periods, as UV light can degrade the adhesive. Store the helmet in a cool, dry place. If you need to remove an adhesive mount, peel it off slowly and carefully. You can use a plastic scraper or old credit card to help lift the edge without damaging the helmet. Any adhesive residue can be removed with rubbing alcohol and a cloth.

Frequently Asked Questions

Will the adhesive mount damage my helmet?

The adhesive mount will leave a residue mark on the helmet surface, but it will not crack or weaken the helmet itself. If you remove the mount later, you can clean off the adhesive with rubbing alcohol. The spot where the mount was may look slightly different from the rest of the helmet, but the helmet remains safe to use.

Can I use a GoPro mount on a motorcycle helmet?

Yes, but motorcycle helmets are heavier and experience more wind force than bicycle or sports helmets. Use the adhesive mount on a smooth, flat area of the helmet, and make sure it is fully cured before riding. Test it at low speeds first. Some riders prefer the helmet strap mount on motorcycles because it distributes the weight more evenly and is easier to remove if you need to take the helmet off frequently.

What if my helmet has a textured or bumpy surface?

Textured surfaces reduce the contact area for adhesive and make mounts less stable. The helmet strap mount is your best option because it does not rely on adhesive. If you want to use an adhesive mount, look for the smoothest spot on the helmet, clean it thoroughly, and consider using a rougher adhesive pad designed for textured surfaces. Check the mount instructions to see if they mention textured helmets.

How do I know if the camera is pointing the right direction?

Before you film, put on the helmet and look in a mirror or have someone take a photo of you wearing it. You will see exactly what the camera sees. Most GoPro mounts allow you to adjust the angle slightly by rotating the camera or the mount arm. Make small adjustments and test again until the angle captures what you want.

Can I attach a GoPro to a helmet while wearing it?

You can attach a helmet strap mount while wearing the helmet, but you should remove the helmet to attach an adhesive mount. It is easier to clean the surface, explore the adhesive, and position the mount accurately when the helmet is off and sitting on a flat surface. For adhesive mounts, take the helmet off, do the preparation and attachment, wait 24 hours, and then put it on to test the camera angle.