The GoPro Hero 3 charges through a micro-USB port on the side of the camera, using the included USB cable and power adapter

The GoPro Hero 3 has a built-in rechargeable lithium battery that you charge while the battery is still inside the camera. You do not need to remove the battery to charge it. Plug the included USB cable into the micro-USB port on the side of the camera (the port is small and rectangular), then plug the other end into a power source — either the wall adapter that came with your camera or any standard USB power adapter.

The camera will show a red light while charging and a green light when fully charged. A full charge typically takes two to three hours, depending on how depleted the battery was. You can use the camera while it is charging, though this will slow down the charging process.

Key Takeaways

  • The micro-USB port is located on the side of the camera and accepts the included USB cable.
  • A red indicator light means the battery is charging; green means it is fully charged.
  • Full charging takes two to three hours from a completely empty battery.
  • You can charge the camera using any standard USB power adapter, not just the one included in the box.
  • The battery stays inside the camera during charging — you do not need to remove it.

Where to find the charging port

The micro-USB charging port is on the right side of the GoPro Hero 3 when you are looking at the camera from behind. It is a small rectangular opening, smaller than a standard USB port. The port sits near the bottom edge of the side panel, close to where the camera's housing seals.

The cable that came in your box has a flat, rectangular connector on one end that fits into this port. If you are using a different USB cable, make sure the connector is micro-USB — it will be noticeably smaller than a standard USB connector. Push the cable in gently until you feel it seat; it should not require force.

Using the included power adapter versus other chargers

The GoPro Hero 3 box includes a wall adapter with a USB port on it. You plug the USB cable into this adapter, then plug the adapter into a wall outlet. This is the fastest way to charge the camera because wall outlets deliver consistent power.

You can also charge the camera using any USB power adapter — the kind you might use for a phone or tablet — as long as it has a standard USB port. You can even charge from a computer's USB port, though this will be slower because computers typically deliver less power than a wall adapter. A car charger with a USB port works as well. The camera will charge from any of these sources; it straightforward adjusts to whatever power is available.

How to know when charging is complete

While the battery is charging, a red light on the back of the camera (near the screen) will be lit. This light stays on the entire time power is flowing into the battery. When the battery reaches full charge, the red light turns off and a green light appears in its place. Once you see the green light, the battery is fully charged and you can unplug the cable.

If the light does not change after several hours, or if the camera does not respond to being plugged in, the issue is usually a loose connection. Unplug the cable, check that the micro-USB connector is clean and free of dust, and plug it back in firmly. If the problem continues, the USB cable itself may be damaged — try a different micro-USB cable if you have one available.

Charging time and battery life expectations

A completely empty GoPro Hero 3 battery takes two to three hours to reach full charge when using the wall adapter. If you are charging from a computer USB port or a lower-power adapter, add another hour or two to that estimate. The camera will continue to charge even if you are using it, but the process will take longer because some of the power goes to running the camera instead of the battery.

Once fully charged, the battery will power the camera for roughly one and a half to two hours of continuous recording, depending on which recording mode and resolution you are using. Higher resolutions and frame rates drain the battery faster. If you plan to record for longer than that, charge a second battery beforehand or bring the charger with you so you can top up during breaks.

Troubleshooting a camera that will not charge

If you plug in the camera and no light appears, first check that the power source itself is working — plug a phone charger into the same outlet or USB port to confirm. Then inspect the micro-USB port on the camera for debris. Lint, dust, or sand can block the connection. Use a dry cotton swab or a small flashlight to look inside the port, and gently clean it if you see anything blocking the opening.

Next, try a different USB cable if you have one. The cable that came with your camera can wear out or develop internal breaks that are not visible from the outside. If a different cable works, the original cable is faulty and should be replaced. If the camera still does not charge with a different cable and a different power source, the charging port itself or the battery may be damaged, and you should contact GoPro support or take the camera to an authorized repair center.

Extending battery life between charges

You can stretch the time between charges by turning off features you are not using. Disable Wi-Fi if you are not controlling the camera remotely. Turn off the LCD screen on the back if you are not reviewing footage. Use a lower resolution or frame rate if the situation allows — 1080p at 30 frames per second uses less power than 4K recording. These changes will noticeably extend how long the battery lasts on a single charge.

Store the camera in a cool place when you are not using it. Heat drains lithium batteries faster, so avoid leaving the camera in direct sunlight or in a hot car. If you will not be using the camera for more than a few weeks, charge the battery to about 50 percent and store it in a cool, dry place. This is gentler on the battery's long-term health than storing it fully charged or completely empty.

Frequently Asked Questions

Can I charge the GoPro Hero 3 with a phone charger?

Yes, as long as the phone charger has a USB port and you use a micro-USB cable. Any standard USB power adapter will work. The camera will charge at whatever speed the adapter provides — a higher-power adapter will charge faster than a lower-power one, but any of them will eventually fully charge the battery.

Why is my camera showing a red light but not charging?

A red light means the camera is powered on, not necessarily that it is charging. Check that the USB cable is firmly seated in the micro-USB port. If the cable is loose, the camera may turn on but not actually charge. Unplug and reconnect the cable, making sure you hear or feel a click. If the light is still red after reconnecting, try a different USB cable or power source.

How long does a fully charged battery last?

A full battery typically powers the camera for one and a half to two hours of continuous recording. The exact time depends on which resolution and frame rate you are using — 1080p uses less battery than 4K, and 30 frames per second uses less than 60 frames per second. Wi-Fi and the LCD screen also drain the battery faster when they are on.

Can I use the camera while it is charging?

Yes, you can record or review footage while the camera is plugged in and charging. The charging process will be slower because some of the incoming power goes to running the camera, but the battery will still charge. This is useful if you need to keep recording but also need to top up the battery between sessions.

What should I do if the charging port is damaged?

If the port is cracked, bent, or will not accept the USB cable, the camera cannot charge through that port. Contact GoPro support to discuss repair options, or take the camera to an authorized repair center. Do not attempt to force the cable into a damaged port, as this can cause further damage.