Factory Reset Wipes All Settings and Footage—Here's How to Do It
A factory reset on your GoPro Hero 3 erases all your custom settings, WiFi connections, and any video or photos stored on the camera's internal memory, returning it to the state it left the factory. You do this through the camera's menu system using the buttons on the back, and it takes about two minutes. This is useful when the camera is freezing, refusing to connect to WiFi, or you're preparing to sell or give it away.
Before you start, understand that a factory reset deletes everything on the camera itself—not on an SD card. If you have footage you want to keep, copy it to a computer first. The reset does not affect files on an external memory card, only the camera's internal storage and settings.
Key Takeaways
- A factory reset erases all settings, WiFi pairings, and files stored in the camera's internal memory, but does not touch an SD card.
- You access the reset through the camera menu by pressing the back button to navigate to Settings, then Delete All.
- The process takes about two minutes and the camera will restart automatically when finished.
- Back up any footage to your computer before resetting, since internal files cannot be recovered afterward.
Charge the Battery Before You Start
Plug your Hero 3 into a USB charger or connect it to a computer with the included USB cable. Let it charge for at least 30 minutes so the battery is at 50 percent or higher. A factory reset can take a few minutes, and if the battery dies mid-reset, the camera may not restart properly.
Do not attempt a factory reset if the battery is low or the camera is powered by USB alone. The camera needs enough stored power to complete the process and restart.
Navigate to the Settings Menu
Power on the camera by pressing the power button on the back (the button closest to the LCD screen). Wait for the camera to fully boot—you'll see the GoPro logo and then the main screen with recording mode options.
Press the back button (the button on the right side of the camera, below the power button) once. This opens the menu. You'll see options like Video, Photo, and Burst. Press the back button again to move deeper into the menu system until you see "Settings" appear on the screen.
Find and Select Delete All
Once you're in Settings, use the back button to scroll down through the options. You're looking for "Delete All" or sometimes labeled as "Format" depending on your Hero 3 firmware version. The menu scrolls slowly, so be patient—it may take several presses to reach it.
When "Delete All" appears on the screen, press the shutter button (the large button on top of the camera) to select it. The camera will ask you to confirm. Press the shutter button again to confirm that you want to erase everything.
Wait for the Reset to Complete
After you confirm, the screen will show a progress indicator or a message saying the camera is resetting. This process takes about 60 to 90 seconds. Do not turn off the camera, remove the battery, or unplug it during this time.
When the reset finishes, the camera will restart automatically and show the startup screen again. The LCD screen may be blank or show the GoPro logo for a few seconds—this is normal. Once you see the main recording menu, the reset is complete.
Verify the Reset Worked
Check that your custom settings are gone by pressing the back button to enter Settings again. You should see the default options: Video resolution set to 1080p, frame rate at 30fps, and no WiFi network connected. If you had named your camera or set a custom date, those will be reset to factory defaults.
If the camera still shows your old settings or won't turn on after the reset, try charging it for another 30 minutes and powering it on again. In rare cases, a second reset attempt may be necessary.
What to Do If the Reset Fails
If the camera freezes during the reset or won't restart afterward, remove the battery for 30 seconds, then reinsert it and power the camera on. This forces a hard restart. If the camera still won't respond, plug it into a computer with a USB cable—sometimes the camera will boot into a recovery mode that allows it to finish the reset process.
If you're still stuck after a hard restart and USB connection, the camera may have a hardware issue unrelated to the reset. At that point, contact GoPro support or consult the warranty information that came with your camera.
Frequently Asked Questions
Will a factory reset erase files on my SD card?
No. A factory reset only erases the camera's internal memory and settings. Any video or photos stored on an SD card remain untouched. If you want to erase the SD card as well, you must format it separately through the camera menu.
Can I recover files after a factory reset?
Files stored in the camera's internal memory cannot be recovered after a factory reset. If you have footage you need, copy it to a computer before resetting. SD card files are not affected by the reset.
How long does a factory reset take?
The reset process itself takes about 60 to 90 seconds. The camera will restart automatically when finished. Do not turn off the camera during this time.
Do I need to remove the SD card before resetting?
No, you can leave the SD card in the camera. The reset will not touch it. However, if you want to be extra cautious, you can remove it beforehand—just make sure the camera is powered off first.
What if my Hero 3 won't turn on after the reset?
Charge the battery for at least 30 minutes, then try powering it on again. If it still won't start, remove the battery for 30 seconds, reinsert it, and try again. If the camera remains unresponsive, connect it to a computer via USB cable to see if it enters recovery mode.