Where the SD card slot is and how to open it
The SD card slot on a GoPro is located on the side of the camera body, behind a small rubber door. On most GoPro models — including the Hero 11, Hero 10, and Hero 9 — this door sits on the left side when you're holding the camera facing forward. The door is labeled with a small SD card icon so you can spot it quickly.
To open the door, use your fingernail or a plastic tool to gently pry the edge outward. The door is hinged at the bottom, so it swings down and away from the camera. Do not force it; if it resists, you are likely pulling at the wrong angle. Once open, you will see a small rectangular slot inside.
Some older GoPro models, like the Hero 8 and earlier, have the slot in slightly different locations or require a different opening method. Check your camera's manual if the side slot does not exist on your model.
Key Takeaways
- The SD card slot is behind a rubber door on the side of your GoPro, marked with an SD card symbol.
- Push the card straight in until you hear or feel a click, which means it is fully seated.
- To remove the card, push it in gently until it clicks and springs back out on its own.
- Use a microSD card with a capacity of 64 GB or higher and a speed class of V30 or faster for smooth 4K recording.
- Always power off your GoPro before inserting or removing the card to avoid corrupting files.
Inserting the SD card into the slot
Hold the SD card with the gold contacts facing into the camera and the label facing outward toward you. The card should slide in horizontally, not at an angle. Position it so the corner with the notch aligns with the slot opening.
Push the card straight in with steady, even pressure. You will feel slight resistance as it enters. Continue pushing until you hear a soft click or feel the card stop — this click means the card is fully seated and locked in place. If the card does not click, it is not inserted far enough and may fall out or not be recognized by the camera.
Once inserted, close the rubber door by swinging it back up and pressing it firmly until it sits flush with the camera body. The door should seal completely with no gaps.
Checking that the card is recognized
Power on your GoPro and look at the screen. If the card is inserted correctly, the camera will display the remaining storage space and battery level. If you see a message saying "No SD Card" or the storage space does not appear, the card is not fully seated.
Power off the camera, open the door again, and push the card in a bit further. Sometimes the first attempt does not go all the way. Repower the camera and check the screen again.
If the camera still does not recognize the card after reinserting it, the card itself may be damaged or incompatible. GoPro recommends using cards from manufacturers like SanDisk, Kingston, or Lexar with a speed rating of V30 or higher.
Removing the SD card safely
Always power off your GoPro before removing the card. This prevents the camera from writing data to the card at the moment you pull it out, which can corrupt files or damage the card.
Open the rubber door on the side of the camera. Locate the SD card in the slot. Push the card gently straight in — it will click and then spring back out toward you on its own. Catch it as it ejects so it does not fall.
Do not yank or pull the card out by force. The spring-eject mechanism is designed to push it out safely when you press it in. If you pull instead, you risk bending the card or damaging the slot contacts.
What to do if the card is stuck
If the card will not eject when you press it in, do not force it. Power off the camera completely and wait a few seconds. Sometimes the camera is still writing data in the background even after you press the power button.
Try pressing the card in again with gentle, steady pressure. If it still does not eject, the card may be physically stuck due to dust or debris in the slot. Use a clean, dry cloth to gently wipe around the edges of the card and the slot opening, then try again.
If the card remains stuck after these steps, contact GoPro support or visit a camera repair shop. Forcing a stuck card can damage both the card and the camera's internal slot mechanism.
SD card size and speed recommendations
GoPro cameras work with microSD cards, not full-size SD cards. The most common sizes are 64 GB, 128 GB, 256 GB, and 512 GB. For 4K recording at high frame rates, a 128 GB card or larger is practical because 4K video uses about 1 GB of storage per minute.
The card's speed class matters for recording stability. Look for a V30 rating on the card's label — this means the card can write data at a minimum of 30 MB per second, which is the baseline GoPro requires for 4K without dropped frames. V60 and V90 cards are faster and more reliable but cost more.
Avoid very cheap or off-brand cards. They may work for a few recordings but often fail or corrupt files during longer sessions. SanDisk Extreme, Kingston Canvas Go, and Lexar Professional are reliable choices that work well with GoPro cameras.
Frequently Asked Questions
Can I use a regular SD card instead of a microSD card?
No. GoPro cameras use microSD cards only. A full-size SD card will not fit in the slot. If you have a full-size card, you can use an SD-to-microSD adapter, but the card itself must be microSD format.
What happens if I insert the card upside down?
The card will not fit into the slot if it is upside down or backwards. The notch on the corner of the card is designed to prevent incorrect insertion. If the card does not slide in smoothly, flip it over or rotate it and try again.
Do I need to format the card in the camera before using it?
It is a good idea to format a new card in your GoPro before recording. This prepares the card for the camera's file system. Go to Settings, then Storage, and select Format Card. This erases any existing data, so only do this if the card is empty or you have backed up the files elsewhere.
Can I remove the card while the camera is recording?
No. Always stop recording and power off the camera before removing the card. Removing the card during recording will corrupt the video file and may damage the card.
How do I know if my card is failing?
Signs of a failing card include the camera not recognizing it, files disappearing after recording, or the camera freezing during playback. If you see these signs, stop using the card when ready and back up any files to a computer. Replace it with a new card.