Where the SD card slot is and how to open it

On the naked GoPro models — the ones without a housing — the SD card slot is on the right side of the camera body when you're looking at the screen. You'll see a small rectangular door with a tiny latch. Push that latch gently downward and the door will swing open, revealing the slot inside.

The slot itself is a narrow opening about the size of a postage stamp. This is where the SD card goes. The door is hinged at the bottom, so it swings down and out of the way once you've released the latch. Don't force it — if it's not opening smoothly, you're probably pushing the latch in the wrong direction.

Key Takeaways

  • The SD card slot is on the right side of the naked GoPro body, accessed by pushing down a small latch to open the door.
  • Insert the card with the gold contacts facing into the camera and the label facing outward toward you.
  • Push the card straight in until you hear or feel a click, which means it's seated properly in the slot.
  • The card will sit flush with the camera body once fully inserted — if it's sticking out, it's not all the way in.
  • Always power off the camera before inserting or removing the SD card to avoid corrupting files.

Positioning the card correctly before you insert it

Before you slide the card into the slot, orient it so the gold contact pins are facing into the camera. The label side of the card — the side with any printing on it — should face outward toward you. This is the only way the card will fit; if you try to insert it backwards or sideways, it straightforward won't go in.

Hold the card between your thumb and forefinger at the corners, not on the gold contacts. The contacts are delicate and can be damaged by oils from your skin or by scratching. A clean, dry card works better than one that's been handled a lot.

Sliding the card into the slot

With the door open and the card oriented correctly, align the card with the slot opening. Slide it straight in, moving it directly away from you and into the camera body. Don't angle it or twist it — just a straight, steady push.

You'll feel the card move into the slot. Keep pushing gently until you hear a small click or feel a slight resistance change. That click means the card has reached the end of the slot and is seated properly. The card should now sit flush with the camera body, not sticking out at an angle.

Closing the door and checking the fit

Once the card is fully inserted, swing the door back up and push the latch upward to lock it. The latch should click into place. The door should be flush with the camera body — if there's a gap, the latch isn't fully engaged and you should try again.

Power on the camera and check the screen. The camera should recognize the card within a few seconds. If you see a message about an unrecognized or unformatted card, that's normal for a new card — the camera will walk you through formatting it the first time you use it. Formatting erases anything on the card and prepares it for recording.

What to do if the card won't go in

If you're pushing and the card isn't sliding in smoothly, stop and check the orientation. The gold contacts must face into the camera, and the label must face toward you. If you've got that right and it still won't budge, the slot may have debris in it — a speck of dust or lint can block the opening.

Use a flashlight to look into the slot. If you see anything inside, use a dry cotton swab or a clean, dry cloth to gently wipe the inside of the slot. Don't use liquids or compressed air, which can push debris deeper in or damage the contacts inside the slot. Once the slot is clear, try inserting the card again.

Removing the SD card when you need to

To remove the card, power off the camera first. Open the door the same way you did to insert it — push the latch down and swing the door open. The card will be sitting flush in the slot. Push the card gently inward (toward the camera) and it will spring back out slightly. Grab the edge and pull it straight out toward you.

Don't yank on the card or remove it while the camera is recording or powered on. Pulling the card out during recording can corrupt the files on it and make them unplayable. Always shut down the camera first, wait a few seconds, and then remove the card.

Card types and compatibility

Naked GoPro models work with standard microSD cards and full-size SD cards, depending on which model you have. Check your camera's manual or the specs on GoPro's website to confirm which size your model uses. A microSD card is much smaller — about the size of a fingernail — while a full-size SD card is roughly the size of a postage stamp.

The camera doesn't care about the brand, but it does care about the speed. GoPro recommends cards rated for at least 60 Mbps write speed, especially if you're recording in high resolution or high frame rates. A slower card may work, but you risk dropped frames or corrupted footage. Check the card's packaging or the manufacturer's website for the speed rating.

Frequently Asked Questions

Can I insert the SD card while the camera is on?

You can, but you shouldn't. Inserting or removing the card while the camera is powered on can corrupt the files on the card or damage the slot. Always power off the camera, wait a few seconds for it to fully shut down, and then insert or remove the card.

What does it mean if the camera says the card is unformatted?

An unformatted card is one the camera hasn't prepared for recording yet. This is normal for a brand-new card. The camera will offer to format it for you — select yes, and it will erase anything on the card and set it up for recording. Formatting takes a minute or two.

How do I know if the card is inserted all the way?

The card should sit completely flush with the camera body once it's fully inserted. If any part of the card is sticking out, it's not all the way in. Push it gently until you feel the click and the card no longer protrudes.

Can I use the same SD card in other cameras?

Yes. SD cards are standard, so a card that works in your GoPro will work in most other cameras, phones, and computers with an SD card slot. Just remember that formatting the card in a different device will erase everything on it.

What should I do if the card slot is damaged or the latch won't close?

If the latch is broken or the door won't stay closed, the camera may not recognize the card properly, and water or dust could get inside. This is a hardware issue that you can't fix at home. Contact GoPro support or take the camera to an authorized repair center.