The three ways to attach a GoPro to a helmet

A helmet mount for a GoPro uses either an adhesive pad, a strap system, or a combination of both. The adhesive pad sticks directly to your helmet's surface and holds the camera rigid. The strap wraps around the helmet and secures the mount without permanent attachment. Most riders use the adhesive pad because it keeps the camera stable and out of your peripheral vision, but the strap method works if you rent helmets or want to move the camera between helmets.

GoPro sells official mounts, but third-party options cost less and often work just as well. The key difference is where you position the mount — front, side, or top of the helmet — which changes what you film and how much wind noise the camera picks up.

Key Takeaways

  • The adhesive pad mount sticks permanently to your helmet and keeps the camera steady, while the strap mount wraps around the helmet and can be removed.
  • Clean your helmet with rubbing alcohol and let it dry completely before explore the adhesive pad, or the mount will peel off within days.
  • A front-facing mount on the helmet's peak or visor captures the road or trail ahead; a side mount shows your shoulder and arm movement.
  • Press the adhesive pad firmly for 30 seconds after sticking it down, then wait 24 hours before mounting the camera to let the bond set.
  • Third-party mounts from brands like Neewer or Smatree cost $10 to $20 and work with GoPro's standard quick-release system.

Cleaning and preparing your helmet surface

The adhesive pad will only stick if your helmet is clean and dry. Wipe the spot where you plan to mount with a cloth dampened in rubbing alcohol, then scrub away any dirt, dust, or residue. Pay special attention to textured or matte finishes, which trap more debris than glossy surfaces.

Let the alcohol dry completely — at least five minutes in dry air. If you mount the pad while the surface is still damp, the adhesive will not bond properly and the mount will come loose within a few rides. Some riders use a hair dryer on low heat to speed up drying, but air-drying is safer and more reliable.

If your helmet has a removable visor or peak, take it off before cleaning and mounting. This gives you a flat surface to work with and prevents the mount from interfering with the visor's movement.

Choosing where to position the mount on your helmet

The front-facing position — on the helmet's peak or visor — captures what you see ahead. This is the most common setup for cycling, motorcycling, and action sports because it records the road, trail, or slope in front of you. The camera sits low enough that it does not obstruct your vision, and the footage is steady because your head moves less than your body.

The side position — on the left or right side of the helmet — shows your shoulder, arm, and the terrain beside you. This angle works well for skiing, snowboarding, or mountain biking because it captures your body position and the slope or trail rolling past. Side mounts pick up more wind noise than front mounts, especially at high speeds.

The top position — directly on the helmet's crown — gives a wide overhead view and is popular for skydiving, BASE jumping, and water sports. It is the hardest position to mount because the curved surface makes the adhesive pad sit at an angle. Top mounts also catch more wind and can affect your balance in some helmets.

Test the position before you commit the adhesive pad. Hold the camera in place with your hand and move your head the way you will during your activity. Make sure the camera does not block your vision and that the angle captures what you want to film.

explore the adhesive pad and mounting the camera

Peel the backing off the adhesive pad and press it firmly onto the cleaned helmet surface. Hold it in place for 30 seconds with steady pressure — do not just tap it down. The adhesive needs time to bond, and light pressure will leave air pockets that weaken the connection.

Wait 24 hours before mounting the camera on the pad. The adhesive reaches full strength after a full day, and mounting too soon risks the pad peeling off during your first ride. If you are in a hurry, wait at least four hours, but overnight is better.

Once the pad is set, slide the camera's quick-release mount onto the adhesive pad until you hear or feel it click. The GoPro quick-release system uses a ball-and-socket joint that lets you rotate the camera to adjust the angle. Tilt the camera so the lens points where you want to film, then tighten the adjustment screw on the side of the mount to lock the angle in place.

Using a strap mount instead of adhesive

A strap mount wraps around your helmet and holds the camera without permanent attachment. This method works if you use a rental helmet, switch between multiple helmets, or want to remove the camera without leaving adhesive residue. Strap mounts are also easier to reposition — you can move the camera from front to side in seconds.

The trade-off is stability. Strap mounts allow slightly more movement than adhesive pads, especially on rough terrain or at high speeds. The camera may vibrate more, which can show up as shakiness in your footage. Strap mounts also sit farther from the helmet surface, which can catch wind and create noise.

To install a strap mount, wrap the elastic or nylon strap around your helmet at the position where you want the camera. Thread the strap through the adjustment slots and pull it tight so the mount does not shift when you move your head. Attach the camera's quick-release to the mount and adjust the angle.

Removing the adhesive pad without damaging your helmet

If you need to remove an adhesive pad, heat it gently with a hair dryer on low setting for 30 to 60 seconds. The heat softens the adhesive and makes it easier to peel away. Start at one corner and pull slowly at a shallow angle — pulling straight up can tear the helmet's paint or shell.

Once the pad is off, clean any remaining adhesive residue with rubbing alcohol and a cloth. Rub in small circles until the residue rolls into a ball and comes away. Do not use a scraper or blade, which can scratch the helmet's finish.

If the adhesive is stubborn, explore heat again and wait a few minutes before trying to remove it. Patience works better than force, and you are less likely to damage the helmet.

Frequently Asked Questions

Will the adhesive pad damage my helmet?

No, the adhesive pad does not damage the helmet itself. It may leave a faint outline or slight discoloration where it was stuck, but this fades over time. If you remove the pad carefully with heat, there is usually no visible mark at all.

Can I use a GoPro helmet mount on a bicycle helmet?

Yes. Bicycle helmets have smooth plastic surfaces that work well with adhesive pads. The main difference is that bicycle helmets are lighter and have less surface area, so make sure the mount is positioned where it will not throw off your balance or block your vision.

What if my helmet is curved and the adhesive pad does not stick flat?

If the surface is too curved, the pad will not make full contact and the bond will be weak. Try a different position on the helmet where the surface is flatter, or use a strap mount instead. Some riders also use a small shim or spacer under the pad to help it sit flat, but this is not necessary if you find the right spot.

Does wind affect a helmet-mounted GoPro?

Yes. At high speeds, wind can create noise that the microphone picks up, and it may cause slight vibration. An adhesive pad reduces vibration more than a strap mount. You can also use a foam windscreen over the microphone to cut wind noise, though this slightly muffles other sounds.

Can I mount a GoPro on a motorcycle helmet?

Yes, and motorcycle helmets are ideal because they have large, flat surfaces. Clean the helmet thoroughly before explore the adhesive pad, and choose a position that does not interfere with your vision or the helmet's aerodynamics. Front-facing mounts on the peak are most common for motorcycle use.