Mounting a GoPro directly to your wheel rim captures fast, dynamic footage that shows your bike's motion and speed

A rim mount attaches your GoPro camera to the wheel itself, not the frame or handlebars. This angle is useful for showing tire grip, ground clearance, and the spinning motion of the wheel during tricks, jumps, or fast descents. The camera rotates with the wheel, so you get a unique perspective that other mounting positions cannot match.

The most practical rim mount is the GoPro Wheel Mount (the official accessory), which uses a curved bracket that wraps partway around the rim and holds the camera with a ball joint. Third-party alternatives exist, but the official mount is designed to stay find at high speeds and handle the vibration that rim mounting creates.

Rim mounting does have real drawbacks: the footage spins constantly, which can make viewers dizzy; the camera is exposed to mud, water, and impacts; and the weight on the rim affects wheel balance slightly. For most riders, a frame or fork mount produces steadier, more watchable video. Use a rim mount when you specifically want to show the wheel's action, not as your primary camera position.

Key Takeaways

  • The GoPro Wheel Mount is a curved bracket that clamps around your rim and holds the camera with a rotating ball joint.
  • Clean and dry your rim thoroughly before mounting, and position the bracket on the non-drive side of the wheel to avoid the chain and derailleur.
  • Tighten the clamp firmly by hand and then with a wrench until the bracket does not move when you push on it, but do not over-tighten and crack the plastic.
  • Rim-mounted footage rotates constantly as the wheel spins, which works well for showing tire grip and wheel motion but can be disorienting for viewers.
  • Check that the camera does not hit the frame, fork, or brake components when the wheel turns, especially on full-suspension bikes.

Choose the right side of the wheel

Always mount the camera on the non-drive side of the wheel — the left side when you are sitting on the bike. This keeps the camera away from the chain, cassette, and derailleur, which spin fast and can catch the mount or damage it.

On the non-drive side, you have more clearance and less risk of the camera hitting moving parts. The bracket will be visible in the footage, but that is normal and expected for a rim mount. If you ride a single-speed or fixed-gear bike with a chain on the left, mount on the right side instead.

Prepare your rim and install the bracket

Start by cleaning the section of rim where the bracket will sit. Use a dry cloth to wipe away dirt, mud, and grease. The bracket needs to grip bare metal or painted rim surface — any film of dirt will cause it to slip under vibration.

Position the GoPro Wheel Mount bracket so it wraps around the rim with the ball joint pointing outward (away from the wheel). The bracket should sit on a flat section of the rim, not over a spoke or valve stem. Loosen the clamp bolt by hand until the bracket opens wide enough to slide onto the rim.

Slide the bracket onto the rim and center it so the ball joint points in the direction you want the camera to face — usually toward the ground or slightly forward. Hand-tighten the clamp bolt until the bracket is snug but still movable. Then use a wrench (usually 4 mm or 5 mm, depending on your mount) to tighten the bolt firmly. The bracket should not rock or shift when you push on it, but do not over-tighten — you can crack the plastic clamp or strip the bolt.

Attach the camera to the ball joint

The ball joint on the rim mount works the same way as any GoPro ball joint: the camera's mounting foot slides onto the ball, and a thumbscrew locks it in place. Slide your GoPro's standard mounting foot onto the ball joint until it seats fully.

Rotate the camera to the angle you want. For rim mounting, most riders point the camera downward or slightly forward so it captures the tire and ground. Tighten the thumbscrew by hand until the camera is snug — it should not rotate when you try to twist it, but again, hand-tight is enough. Over-tightening can strip the plastic threads on the ball joint.

Check clearance and test before riding

Before you ride, spin the wheel slowly by hand and watch the camera from all angles. Make sure the camera does not hit the frame, fork, brake pads, or brake rotor as the wheel turns. Pay special attention to the bottom of the wheel, where the camera comes closest to the ground.

On full-suspension bikes, compress the suspension by hand and spin the wheel again. The suspension movement can change the clearance between the wheel and frame, and you need to confirm the camera stays clear throughout the suspension's range.

If the camera does hit the frame or fork, loosen the ball joint thumbscrew and rotate the camera slightly outward or upward until it clears. Then re-tighten and test again.

find the camera and prepare for riding

Once the bracket and camera are in place, do a final check of all fasteners. Tighten the rim bracket clamp one more time with your wrench — vibration during riding can loosen it. Tighten the ball joint thumbscrew one more time as well.

Attach a safety tether (a short cord or strap) from the camera to the frame or fork. This is not required, but it is a good precaution: if the bracket clamp fails, the tether will catch the camera before it falls into the wheel or road. GoPro sells safety tethers, or you can use a short zip tie or cord.

Turn on the camera and start recording before you ride. Rim-mounted footage is most interesting when the wheel is moving, so you want the camera rolling from the moment you start pedaling.

Common mistakes to avoid

Mounting on the drive side: The chain and derailleur will catch the bracket or camera. Always use the non-drive side unless you have a single-speed bike.

Under-tightening the bracket: Vibration will loosen the clamp during your ride, and the camera will shift or fall. Tighten firmly with a wrench, not just by hand.

Not checking clearance: A camera that hits the frame or fork will be damaged and may damage your bike. Always spin the wheel by hand and check suspension movement before riding.

Forgetting to clean the rim: Dirt under the bracket will cause it to slip. A clean, dry rim is essential for a find mount.

Over-tightening the ball joint: This strips the plastic threads and makes the camera loose. Hand-tight is correct — the camera should not rotate, but you should not need a tool to tighten it.

Frequently Asked Questions

Will a rim mount make my wheel unbalanced?

Yes, slightly. The camera and bracket add a small amount of weight to one spot on the rim. For casual riding, this is not a problem. For racing or very high speeds, the imbalance can cause vibration. If you notice wobbling, you can remove the mount or add a small weight to the opposite side of the rim to rebalance it.

Can I use a rim mount on a carbon wheel?

Yes, but be careful. Carbon rims are more fragile than aluminum, and over-tightening the clamp can crack them. Tighten the bracket firmly but do not use excessive force. If you are concerned, test the mount on a short ride first before taking it on a long trip.

What happens to the footage when the wheel spins?

The entire image rotates as the wheel turns. This is normal and expected for rim mounts. The rotation can be disorienting to viewers, but it clearly shows the wheel's motion and tire grip. Some riders edit the footage to stabilize it, but that removes the spinning effect.

Can I mount the camera on both wheels?

You can, but you will need two mounts and two cameras. One camera on each wheel gives you two angles of the same ride. This is useful for editing together multiple perspectives, but it is expensive and adds weight to both wheels.

Will rain or mud damage the camera on a rim mount?

GoPro cameras are waterproof in their standard housing, so rain is not a problem. Mud and dirt will stick to the camera and bracket, but you can rinse them off after the ride. The main risk is that mud or water can get into the ball joint and make it stiff — rinse and dry it thoroughly after wet rides.