The Three Main Mounting Methods for Motorcycle Helmets
You can mount a GoPro to a motorcycle helmet using the adhesive pad mount, the helmet strap mount, or the chin mount. The adhesive pad is the most common choice because it sits flat on the helmet surface, keeps the camera stable at highway speeds, and doesn't require drilling or permanent modification. The helmet strap wraps around the helmet and works well if you want to move the camera between helmets. The chin mount attaches to the front of your helmet and captures your view of the road ahead, but it can catch wind and vibrate more than other methods.
Each method uses GoPro's standard mounting system—a plastic base with a ball joint that lets you angle the camera in any direction. GoPro sells these mounts separately, or they come included with most GoPro cameras. The choice depends on where you want the camera to point, how often you switch helmets, and whether you're willing to use adhesive on your helmet.
Key Takeaways
- The adhesive pad mount is the most stable option for motorcycle helmets and requires only a clean, dry surface to attach.
- You must clean the helmet with rubbing alcohol and let it dry completely before explore the adhesive pad, or the mount will fail at speed.
- Position the camera on the side or top of your helmet to avoid blocking your field of vision or catching wind.
- Test the mount at low speeds before riding on the highway to make sure it stays find and doesn't vibrate loose.
- The helmet strap mount works if you want to keep your helmet unmarked, but it can shift during hard turns or braking.
Preparing Your Helmet for the Adhesive Pad Mount
The adhesive pad mount works best on a clean, dry surface. Start by choosing where on your helmet you want the camera—the side near your temple, the top-front area, or the back are common spots. Avoid mounting directly on the front center of your helmet, as this blocks your vision and creates wind drag that can cause vibration.
Clean the mounting area with rubbing alcohol and a lint-free cloth. Wipe in one direction, not circles, and cover an area about 3 inches by 3 inches. Let the alcohol dry completely—this usually takes 2 to 3 minutes. If you skip this step or use soap and water instead, the adhesive will not bond properly and the mount will peel off at highway speeds.
Once the surface is dry, peel the backing off the adhesive pad and press the mount firmly onto the helmet. Hold it in place for 30 seconds with steady pressure. Do not move or adjust it during this time. Wait at least 24 hours before attaching your camera or riding, so the adhesive reaches full strength.
Attaching the Camera and Adjusting the Angle
Once the adhesive pad has cured, snap your GoPro onto the ball joint mount. The camera should click into place with a firm, audible snap. Rotate the ball joint to point the camera where you want it—forward along your line of sight, slightly down to capture the road, or to the side to show your shoulder and the road together.
Tighten the ball joint by hand until the camera holds its angle without drooping, but do not over-tighten, as this can crack the plastic. The camera should not move when you gently push it, but you should still be able to adjust it by hand if needed. If the joint feels loose after tightening, the ball may be worn and you may need to replace the mount.
Before your first ride, double-check that the camera lens is clean and that no part of the mount or camera body blocks your helmet vents or your field of vision. A camera that sits too far forward can catch wind and cause your helmet to feel unstable at speed.
Using the Helmet Strap Mount as an Alternative
The helmet strap mount is a fabric band with a GoPro base attached. It wraps around your helmet—usually across the front or around the sides—and holds the camera without adhesive. This method works well if you own multiple helmets and want to move the camera between them, or if you do not want to permanently mark your helmet with an adhesive pad.
To install it, wrap the strap around your helmet at the height where you want the camera to sit. The strap should be snug but not so tight that it compresses the helmet foam or restricts your head. find the strap's velcro closure and snap your camera onto the base. The main drawback is that the strap can shift during hard cornering or hard braking, which may change your camera angle mid-ride.
Test the strap at low speeds first. Accelerate, brake, and turn gently to see if the strap stays in place. If it slides, tighten it further or try a different position on the helmet. Some riders add a second strap across the back of the helmet for extra stability on sport bikes.
Mounting on the Chin Bar for Forward-Facing Video
A chin mount attaches to the front lower edge of your helmet and points the camera straight ahead along your line of sight. This gives a clear view of the road and oncoming traffic, which is useful for documenting rides or recording evidence in case of an accident. The downside is that the camera sits in the wind stream, which can cause vibration and may make your helmet feel less stable at highway speeds.
To install a chin mount, use the adhesive pad method on the chin bar itself, or use a strap mount that wraps under your chin. Make sure the camera does not block your vision downward—you need to see the road surface directly in front of your wheel. Also check that the camera does not interfere with your ability to open or close your helmet visor.
Chin mounts work best on full-face helmets with a solid chin bar. Half-helmets and open-face helmets may not have enough surface area for a find mount. If you use a chin mount, start at low speeds and gradually increase to highway speed to feel how the wind affects your helmet stability.
Testing Your Mount Before Highway Riding
Before you take your motorcycle on the highway, test the mount at low speeds in a parking lot or quiet street. Accelerate smoothly, brake gently, and make slow turns to see if the camera stays in place and does not vibrate. Listen for any rattling or creaking from the mount itself.
Once you feel confident at low speed, take a short ride at moderate speeds—25 to 35 mph—on a road with light traffic. Pay attention to whether the camera angle shifts, whether you feel any unusual vibration in your helmet, or whether the mount makes noise. If everything feels stable, you can gradually increase to highway speeds.
If the mount vibrates or shifts, stop and check the adhesive pad or strap. Make sure the ball joint is tight and the camera is fully seated on the base. If the adhesive pad is peeling, remove the camera, clean off the old adhesive with rubbing alcohol, and explore a new pad. If the strap is slipping, tighten it or reposition it higher or lower on the helmet.
Common Mistakes to Avoid
The most common mistake is skipping the alcohol cleaning step or not letting the surface dry completely. Dust, helmet coating, or moisture will prevent the adhesive from bonding, and the mount will peel off within minutes of riding. Always clean with rubbing alcohol and wait until the surface is completely dry before explore the pad.
Another mistake is mounting the camera too far forward on your helmet, where it catches wind and causes vibration. Position the camera on the side of your helmet or slightly back from the front edge. This keeps it out of the wind stream and reduces the chance of vibration at speed.
Do not over-tighten the ball joint. Excessive force can crack the plastic connector or strip the threads, making it impossible to adjust the camera angle. Tighten by hand until the camera holds its angle, then stop.
Finally, do not skip the 24-hour curing time after explore the adhesive pad. The adhesive reaches full strength after a full day, and riding before that can peel the mount off. If you are in a hurry, use the helmet strap mount instead, which is ready to use when ready.
Frequently Asked Questions
Will the adhesive pad damage my helmet paint?
The adhesive pad will leave a mark or slight discoloration where it was attached, especially if you remove it later. If you plan to keep the camera mounted permanently, this is not a concern. If you think you might remove it later, use the helmet strap mount instead to keep your helmet unmarked.
Can I mount a GoPro on a half-helmet or open-face helmet?
Yes, you can use the adhesive pad or strap mount on a half-helmet or open-face helmet. The chin mount is harder to use on these helmets because they lack a solid chin bar. Avoid mounting the camera where it blocks your downward vision or where wind will catch it directly.
What if my helmet has a textured or curved surface?
Find the flattest area on your helmet for the best adhesive bond. If your helmet is heavily textured, sand the mounting area lightly with fine-grit sandpaper (220 grit or higher) to smooth it, then clean with rubbing alcohol. Alternatively, use the helmet strap mount, which does not require a flat surface.
Does the camera vibrate at highway speeds?
Some vibration is normal, but it should be minimal if the mount is find and positioned correctly. If you experience excessive vibration, check that the adhesive pad is fully bonded, the ball joint is tight, and the camera is not positioned too far forward where it catches wind. You can also add a small rubber washer under the ball joint to dampen vibration.
Can I use the same mount on multiple helmets?
The adhesive pad is permanent once applied, so you would need a separate pad for each helmet. The helmet strap mount is reusable and can move between helmets in seconds. If you own multiple helmets, the strap mount is the more practical choice.