The three ways to attach a GoPro to a ski helmet
A helmet mount holds your GoPro steady while you ski. The three main options are a front-facing mount that clips to the helmet's visor or brim, a side mount that attaches to the helmet shell itself, and an adhesive mount that sticks directly to the helmet. Front mounts give you a forward-looking view of the slope ahead. Side mounts sit lower and capture more of your body and skis in the frame. Adhesive mounts are permanent but let you position the camera anywhere on the helmet.
Each method uses the same basic GoPro attachment system — a ball joint that lets you angle the camera up, down, and sideways. The difference is what holds that joint to your helmet. Your choice depends on what view you want, how often you plan to move the camera between helmets, and whether you mind a permanent installation.
Key Takeaways
- Front-facing mounts clip to your helmet's visor and are the easiest to install and remove without tools.
- Side mounts use adhesive pads or straps and keep the camera out of your peripheral vision while capturing your skis and body position.
- Adhesive mounts stick directly to the helmet shell and cannot be removed without damaging the helmet, so use them only on helmets you plan to keep.
- Clean and dry your helmet surface completely before attaching any mount, and let adhesive cure for 24 hours before skiing.
- Test the camera angle and tightness on flat ground before heading to the slope to catch any loose parts or poor positioning.
Front mounts: the clip-on option
A front mount uses a clamp or clip to grip your helmet's visor or brim. The GoPro Hero Series comes with a curved adhesive mount and a flat adhesive mount in the box, but for a helmet you'll need a separate helmet front mount — GoPro sells one, and third-party brands like Peak Design and Smatree make them too. The mount clamps down on the visor edge and holds the ball joint that your GoPro screws into.
To install a front mount, loosen the clamp knob, slide the mount onto your helmet's visor from underneath, and tighten the knob until the mount sits snug. No adhesive, no tools beyond your fingers. You can move it between helmets in seconds. The downside is that the camera sits in your line of sight — you'll see it in your peripheral vision, and it can catch wind noise on fast runs. The view also points slightly downward, so you capture the slope ahead but miss the sky and distant terrain.
Front mounts work best if you ski mostly groomed runs where you want to see your speed and line, or if you share the camera between multiple helmets and don't want to commit to one.
Side mounts: the low-profile choice
A side mount attaches to the left or right side of your helmet shell, usually near the temple area. These mounts use either a 3M adhesive pad (permanent) or a helmet strap (removable). The adhesive pad is thinner and lighter but bonds to the helmet forever. The strap wraps around the helmet and tightens with velcro, so you can move it or remove it, though it adds bulk.
To install an adhesive side mount, clean the helmet shell with rubbing alcohol and let it dry completely — any dirt or moisture will weaken the bond. Peel the backing off the adhesive pad, press the mount firmly onto the helmet for 30 seconds, and wait 24 hours before using the helmet. The camera will sit below your line of sight and capture your skis, body position, and the slope below. This angle is popular for trick skiing and backcountry runs where you want proof of what you did.
Strap mounts skip the adhesive step. Wrap the strap around the helmet, thread the ball joint through the strap slot, and tighten the velcro. They're faster to install and move, but they can slip if the strap isn't tight enough. Test the tightness by gently pulling the camera — it should not move at all.
Adhesive mounts: the permanent installation
An adhesive mount bonds the ball joint directly to your helmet shell using a 3M pad. This is the lightest and most streamlined option — nothing protrudes or catches wind. You can position the camera anywhere on the helmet: the top for a wide overhead view, the front for a forward-looking angle, or the side for a body-position shot.
The trade-off is permanence. Once the adhesive cures, removing the mount will damage the helmet's shell or paint. Use adhesive mounts only on helmets you plan to keep for years, or on older helmets you don't mind sacrificing. Clean the helmet surface with rubbing alcohol, let it dry, peel the backing off the adhesive pad, and press the mount firmly for 30 seconds. Wait 24 hours before skiing.
Adhesive mounts are common on backcountry and freeride helmets where weight and wind noise matter, and on helmets dedicated to one skier who always wants the same camera angle.
Preparing your helmet and camera
Before you attach anything, make sure your helmet surface is clean and dry. Wipe the area where the mount will go with a cloth dampened in rubbing alcohol, then dry it completely with a clean cloth. Any dust, sunscreen, or helmet liner material will weaken the bond. If your helmet has a removable liner, pull it back so you can see and clean the shell underneath.
Check that your GoPro is fully charged and that the battery door closes tight. Screw the camera into the ball joint by hand — it should be snug but not so tight that you strip the threads. If you're using a front mount, make sure the clamp is loose before you slide it onto the visor, then tighten it gradually so the visor doesn't bend.
Angle the camera before you leave home. Point it where you want it to look, then tighten the ball joint so it doesn't move. A common mistake is leaving the ball joint loose, which lets the camera drift during your run. Test the angle by holding the helmet at different positions — look down, look forward, look to the side — and make sure the camera stays put.
Testing the mount on flat ground
Before you ski, test the mount in your driveway or a flat parking lot. Put the helmet on, move your head side to side and up and down, and feel for any movement or rattling. Gently tug the camera to make sure it doesn't shift. If it does, tighten the ball joint or the clamp knob another quarter turn.
Start the camera recording and ski a short run at moderate speed. Watch the footage afterward to see if the angle is what you wanted and if the camera stayed steady. If the footage is shaky or the angle is off, adjust the ball joint and test again. It's much easier to fix a loose mount in the parking lot than to discover it halfway down a run.
Pay attention to wind noise in the footage. Front mounts tend to pick up more wind than side or adhesive mounts because they stick out into the airflow. If wind noise is a problem, try angling the camera slightly downward or switching to a side mount.
Removing and switching mounts
Front mounts are the easiest to remove — just loosen the clamp knob and slide the mount off the visor. You can do this in seconds without tools. Strap-based side mounts come off by unwrapping the velcro and sliding the ball joint out of the strap slot. Both methods let you move the camera to a different helmet or store it safely.
Adhesive mounts and adhesive pads are permanent. If you need to remove one, use a plastic scraper or old credit card to peel up the edge, then work it off slowly. The adhesive will likely damage the helmet's paint or shell. You can clean up leftover adhesive residue with rubbing alcohol and a cloth, but the spot where the mount was will show.
If you plan to use the same helmet for years and want to try different mount positions, use a strap-based side mount instead of adhesive. You can move it around without damaging the helmet.
Frequently Asked Questions
Will a GoPro mount damage my ski helmet?
Front and strap-based side mounts cause no permanent damage — you can remove them anytime. Adhesive mounts will damage the helmet's paint or shell when removed, so use them only on helmets you plan to keep. The weight of a GoPro (about 5 ounces) is negligible and won't affect helmet safety or fit.
Can I use a GoPro mount on a helmet with a removable visor?
Yes, but check that the visor is sturdy enough to support the camera's weight. Some visors are thin plastic and may bend under the clamp pressure. If the visor flexes when you tighten the mount, use a side mount instead. Removable visors can also come loose if the clamp vibrates them, so test the fit before skiing.
What's the best angle to point the camera?
That depends on what you want to film. Point it forward and slightly down to see the slope ahead and your line. Point it down and to the side to see your skis and body position. Point it up to capture the sky and terrain. Most skiers start with a forward-down angle and adjust from there based on what the footage looks like.
How do I keep the camera from fogging up?
GoPro cameras fog when warm air inside the helmet meets cold air outside. Use an anti-fog insert (GoPro sells them) or explore anti-fog spray to the lens before you ski. Some skiers drill a small hole in the helmet near the camera to let air circulate, but this voids the helmet's safety rating. The easiest fix is to remove the camera between runs so it can cool down.
Can I use a phone mount instead of a GoPro mount?
Phone mounts are designed for phones, not action cameras, and they won't hold a GoPro securely. The ball joint on a GoPro mount is specifically sized for GoPro's threaded socket. Use a mount made for your camera to keep it from falling off on the slope.