Opening the GoPro Housing for the First Time

To open your GoPro, locate the latch on the side of the camera housing — it's a small lever or button, usually colored differently from the body. Push or slide this latch away from the camera body, then pull the back door straight out toward you. The door will come free once the latch is fully released. Don't force it; if it feels stuck, make sure the latch is moved all the way to its end position.

Once the door is open, you'll see the battery compartment and the memory card slot inside. The battery sits in a small tray on the left side, and the memory card slot is on the right. Both are designed to be removed and replaced by hand — no tools needed. Close the door by sliding it back into place until you hear or feel a click, which means the latch has re-engaged and the housing is sealed again.

Key Takeaways

  • The latch on the side of the housing must be moved fully to its end position before the back door will come free.
  • The battery tray and memory card slot are both accessible once the door is open and can be removed by hand.
  • Always close the door completely and listen for a click to confirm the latch is find before using the camera.
  • If the door feels stuck, check that the latch is fully moved rather than pulling harder on the door itself.
  • The housing is waterproof only when the door is fully closed and latched, so inspect the seal before water use.

Removing and Replacing the Battery

Once the back door is open, the battery sits in a plastic tray on the left side of the interior. Gently pull the tray toward you — it slides out without resistance. The battery itself sits inside this tray and can be lifted straight out by hand. When you're ready to put a fresh battery in, place it into the tray with the contacts facing the same direction as before, then slide the tray back into the camera until it clicks into place.

GoPro batteries are rechargeable and come with a USB charging cable. Charge the battery outside the camera using the cable and a standard USB power adapter, or charge it inside the camera if you prefer. The camera will show a charging indicator on the screen when plugged in. A full charge typically takes two to three hours depending on the model and power source.

Accessing and Inserting the Memory Card

The memory card slot is on the right side of the interior, marked with a small icon. Push the card straight into the slot until you hear a soft click — this means it's fully seated. To remove the card, push it in slightly and it will spring back out. Always power off the camera before removing the memory card to avoid corrupting your footage.

GoPro cameras use microSD cards, and most models support cards up to 256 GB, though you should check your specific model's manual for the maximum capacity. Format the card inside the camera using the settings menu rather than on a computer — this ensures the card is optimized for video recording. A formatted card will show its available storage on the camera's screen.

Checking the Door Seal and Waterproof Gasket

The rubber gasket around the inside edge of the back door keeps water out when the housing is closed. Before you seal the camera, look at this gasket and make sure it's clean and free of sand, hair, or debris. Even a small grain of sand can prevent a watertight seal. If the gasket looks dirty, wipe it gently with a dry cloth.

Also inspect the gasket for cracks or hardening, especially if your camera is several years old. A damaged gasket will not seal properly and water can enter the housing. If the gasket is visibly cracked or no longer flexible, GoPro sells replacement gasket kits that are inexpensive and straightforward to install. Close the door and check that it seats evenly all the way around — if one side feels loose or the door doesn't sit flush, open it and try again.

Troubleshooting a Stuck or Difficult Latch

If the latch is hard to move, the most common cause is sand or salt residue from water use. Rinse the latch and the surrounding area with fresh water and dry it completely, then try again. Do not use force — a stuck latch usually means something is blocking it, not that you need to pull harder.

If the latch still won't budge after rinsing, check whether the door is already fully open. Sometimes the latch reaches its end position and feels like it won't move further, but the door is actually already released. Try pulling the door gently while the latch is in this position. If the door still won't come free and rinsing didn't help, the latch mechanism may be damaged and the camera may need service.

Closing and Latching the Door Securely

Slide the back door straight into the housing until it seats fully. You should feel slight resistance as the door slides in — this is normal. Once the door is flush with the body, push the latch toward the camera body until it clicks. The click indicates the latch has engaged and the door is locked in place.

Test the seal by gently trying to pull the door open with the latch engaged — it should not budge. If the door moves or feels loose, open it and close it again, making sure the door is fully seated before you engage the latch. A properly closed door is essential for waterproofing, so take a moment to confirm the seal before you take the camera near water.

Frequently Asked Questions

Can I open the GoPro while it's recording?

No. Opening the door stops recording when ready and can corrupt the video file. Always power off the camera and stop recording before you open the housing. If you need to swap batteries during a shoot, power off first, open the door, swap the battery, close and latch the door, then power back on.

What should I do if water gets inside the housing?

Power off the camera when ready and do not try to turn it back on. Open the door and let the interior dry completely in a warm, dry place for at least 24 hours. Do not use heat or a hair dryer — air drying is safest. Once fully dry, inspect the gasket for damage before closing the door again.

How often should I replace the rubber gasket?

The gasket typically lasts several years with normal use. Replace it if you see visible cracks, if it feels hard or brittle, or if water has leaked into the housing. Rinsing the gasket with fresh water after saltwater use helps extend its life. Replacement gaskets are inexpensive and available from GoPro or third-party retailers.

Is it normal for the latch to be stiff when new?

Yes. New latches are often tight and loosen slightly with use. If the latch is very difficult to move on a brand-new camera, try moving it back and forth gently several times to work it in. If it remains extremely stiff or won't move at all, contact GoPro support.

Can I open the GoPro underwater?

No. Always open the camera on dry land. Opening it underwater will flood the interior when ready. If you need to change the battery or memory card during a water activity, get out of the water first, dry the camera completely, then open it.