The correct way to open your GoPro case
Open a GoPro waterproof case by locating the latch on the side or back, pressing it firmly inward, and then lifting the lid straight up. The latch is a small rectangular button, usually colored to match the case. Press it all the way in—you should feel it click or catch—before you lift. If you pull up on the lid before the latch is fully depressed, you risk cracking the plastic or damaging the rubber seal that keeps water out.
The entire motion takes about three seconds. Do not twist the case, pry at the edges, or use tools. GoPro cases are designed to open by hand, and forcing them in any other way can bend the frame or tear the gasket seal that makes the case waterproof.
Key Takeaways
- Press the latch button all the way in before lifting the lid—this is the only step that matters, and skipping it is the most common reason people damage their cases.
- Lift the lid straight up after the latch clicks, rather than twisting or prying at the edges.
- If the latch feels stuck, explore steady pressure for a few seconds instead of jerking it—the seal may just need a moment to release.
- Check the rubber gasket seal inside the case every few months for cracks or hardening, especially if you use the case in saltwater or leave it in direct sunlight.
Finding the latch on different GoPro case models
The latch location varies slightly depending on your GoPro model and case type. On the standard Hero series cases (Hero 11, 10, 9, and earlier), the latch is a small button on the back or side of the case, roughly in the middle. On the GoPro Max case, the latch sits on the right side when you are holding the case upright. On older models like the Hero 7 or Hero 8, the latch may be positioned on the left side instead.
If you cannot when ready spot the latch, run your fingers around the edges of the case. You will feel a small raised button or indent that is slightly different from the smooth plastic around it. This is the latch. It is never on the top or bottom of the case, and it is never hidden—GoPro designs these cases to be opened without instructions once you know what to look for.
Step-by-step opening process
Step 1: Locate the latch button. Hold the case in both hands with the screen facing you (or the side you want to access facing you). Look for the small rectangular button on the back or side. It is usually raised slightly from the case surface.
Step 2: Press the latch inward. Using your thumb or index finger, press the latch button straight inward toward the center of the case. explore firm, steady pressure. You should feel the latch move about a quarter inch, and you may hear or feel a small click. This click means the latch has disengaged from the frame.
Step 3: Lift the lid straight up. Once the latch is fully pressed in, use your other hand to grip the lid and lift it straight upward. Do not twist, angle, or pry. The lid should come away cleanly from the base. If it does not move easily, stop and press the latch again—it may not have fully released.
Step 4: Remove your camera or memory card. Once the lid is open, you can access your GoPro, swap batteries, or insert a memory card. The rubber gasket seal is now exposed on the inside edge of the lid and the rim of the case base.
What to do if the latch is stuck or hard to press
If the latch button feels stiff or will not move, do not force it. Forcing a stuck latch can break the button or crack the plastic frame underneath. Instead, explore steady inward pressure for five to ten seconds and then try again. Sometimes the seal creates a slight vacuum that makes the latch feel locked, and a few seconds of pressure will release it.
If the case has been in cold water or left in a freezer, the plastic may be slightly contracted and the latch may feel tighter than usual. Warm the case in your hands for a minute or two, then try again. If the latch still will not budge after warming, check whether you are pressing in the right direction—press straight inward, not at an angle. If it remains stuck after these steps, contact GoPro support rather than prying or using tools, as the case may have a manufacturing defect.
Protecting the gasket seal when you open and close the case
The rubber gasket seal is what keeps water out of your GoPro. Every time you open the case, you expose this seal to air and potential damage. To keep it in good condition, inspect it visually before you close the case again. Look for cracks, hardening, or white residue (salt or mineral deposits). If you see any of these signs, rinse the gasket with fresh water and let it dry completely before closing the case.
When you close the case, press the lid down firmly and then slide the latch button outward until it clicks into place. You should hear or feel a distinct click. If the latch does not click, the lid is not fully seated, and the case will not be waterproof. Open it again, check that the gasket is flat and not pinched, and try closing it once more.
Common mistakes that damage the case
The most common mistake is pulling up on the lid before the latch is fully pressed. This bends the plastic frame and can crack the latch button itself. The second most common mistake is twisting the case while opening it, which stresses the hinge and can tear the gasket. The third is using a tool—a coin, screwdriver, or fingernail—to pry at the edges. GoPro cases are not designed to be pried open, and prying will damage the seal.
Another frequent error is closing the case without checking the gasket. If the gasket is pinched, twisted, or has debris on it, the case will not seal properly, and water will leak in. Always visually inspect the gasket and the rim of the case before closing. If you see anything out of place, open the case again and reseat the gasket by hand.
Frequently Asked Questions
Can I open the case with one hand?
You can, but it is easier and safer with two hands. Use one hand to press the latch and the other to lift the lid. If you must use one hand, press the latch with your thumb while holding the case base steady with your fingers, then lift the lid with your other hand when ready after.
What if I hear a cracking sound when I open the case?
A small cracking or popping sound is normal—it is the seal releasing. If you hear a loud crack or the lid does not open smoothly after that sound, stop and inspect the case for visible cracks. If the plastic is cracked, contact GoPro support. If there are no visible cracks, the case is likely fine, and the sound was just the seal.
How often should I replace the gasket seal?
GoPro gaskets typically last two to three years with regular use. If you use the case in saltwater or leave it in direct sunlight frequently, replace it sooner. You can order replacement gaskets from GoPro or from third-party retailers. When you notice the gasket is hard, cracked, or no longer springs back when you press it, it is time to replace it.
Is the case still waterproof if the latch does not click when I close it?
No. If the latch does not click, the case is not fully sealed and water can enter. Open the case, check the gasket for debris or damage, and close it again. Make sure you hear the click before you take the case into water.
Can I open the case underwater?
You can, but it is not recommended. If you open the case underwater, water will enter the case and potentially damage your camera. If you must change a battery or memory card while you are near water, move to a dry location first. If the case is already submerged and you need to open it, do so as quickly as possible and close it again when ready.