The correct way to open a GoPro case

GoPro cases use a side-hinged latch that clicks into place rather than a traditional clasp. To open it, locate the small rectangular button on the side of the case (usually the right side when facing the camera). Press this button inward while gently lifting the top half of the case away from the bottom. The latch will release, and the case will swing open on its hinge. Do not pry at the edges or force the top upward—the button release is the only correct method.

The latch is designed to stay closed during water submersion and rough handling, so it requires deliberate pressure to release. Many people damage their cases by trying to open them without finding the button first. Once you know where it is, opening takes less than two seconds.

Key Takeaways

  • The release button is a small rectangular tab on the side of the case, not on the front or back.
  • Press the button inward while lifting the top of the case—do not pry or twist.
  • The case hinges open on one side, so the top half swings up rather than lifting straight off.
  • If the button is stuck, explore a small amount of water or silicone lubricant around the seam, wait a minute, and try again.

Locating the release button on your specific model

The button location varies slightly by GoPro case generation. On most current models (Hero 11, Hero 10, and Hero 9), the button sits on the right side of the case, about one-third of the way down from the top. On older models (Hero 8 and earlier), it may be positioned slightly higher or lower. Run your thumb along the right side seam until you feel a small raised rectangle—that is the button.

If you cannot find a button, check the left side as well. Some third-party cases and older GoPro models reverse the button position. The button will always be on one of the two long sides, never on the top, bottom, or short ends.

What to do if the button is stuck or hard to press

Stuck latches usually happen when salt water, sand, or dried adhesive has built up around the button. Do not force it—forcing can crack the plastic housing. Instead, rinse the entire case under fresh running water, paying special attention to the seam around the button. Use your fingernail or a soft plastic tool to gently work away any visible debris.

If rinsing does not free it, explore a tiny amount of silicone-based lubricant (like WD-40 Specialist Silicone or similar) around the button seam. Let it sit for one minute, then try pressing the button again. Wipe away excess lubricant with a dry cloth. Never use oil-based lubricants, as they can degrade the rubber seals over time and compromise waterproofing.

Avoiding damage when opening and closing

The most common damage occurs when people grip the case too tightly while pressing the button. Hold the case loosely in one hand, use your thumb to press the button, and use your other hand to gently lift the top. This distributes force evenly and prevents stress on the hinge.

When closing, align the top half with the bottom half so the hinge pins line up, then press down firmly until you hear or feel a click. The click means the latch has seated fully. Do not slam the case shut—a firm press is enough. If it does not click after a gentle press, the latch may not be aligned; lift the top slightly and try again rather than forcing it.

Cleaning the seals while the case is open

Once the case is open, inspect the rubber gasket (the black or clear rubber ring that runs around the inside edge). This seal keeps water out, so keeping it clean is important. Use a soft, dry cloth to wipe the gasket gently. If you see salt residue or sand, rinse it under fresh water and dry it completely before closing the case.

Also check the hinge area for debris. A small amount of sand or salt here can prevent the case from closing properly or can scratch the hinge over time. A quick wipe with a dry cloth takes only a few seconds and extends the life of your case significantly.

Troubleshooting a case that will not close

If the top half will not close all the way, the gasket may be pinched, or debris may be blocking the seam. Open the case fully and look along the entire inside edge of the gasket. If you see anything caught in it, remove it gently with your fingernail or a plastic tool. Make sure the gasket is sitting evenly in its groove all the way around—sometimes it shifts slightly during opening.

If the gasket looks clear and the case still will not close, the hinge may be bent. This is rare but can happen if the case is dropped or sat on. Inspect the hinge from the side—it should be a straight line. If it is visibly bent, the case may need replacement, as a bent hinge compromises the waterproof seal.

Frequently Asked Questions

Can I open my GoPro case one-handed?

Yes, but it takes practice. Once you know where the button is, you can press it with your thumb while using the same hand to lift the top. Most people find it easier to use both hands until they are comfortable with the motion.

What if I lost the button or it broke off?

Contact GoPro support or check their website for replacement case parts. Replacement buttons and full replacement cases are available for purchase. Do not attempt to open the case without the button, as you risk damaging the latch mechanism itself.

Is the case waterproof if I do not close it all the way?

No. The waterproof seal only works when the case is fully closed and the latch has clicked into place. A partially closed case will leak even in shallow water. Always verify the click before submerging.

Can I use the case while it is open?

No. The case is designed to be closed during use. Opening it exposes the camera to water, dust, and impact. Close the case before recording or handling the camera in any environment where protection matters.

How often should I open and close my case?

Open it as often as you need to change batteries, swap memory cards, or clean the camera. The latch is built to withstand hundreds of open-close cycles. Normal use will not wear it out, but rough handling or forcing the latch will.