Power On and Basic Setup

The GoPro Hero 3 powers on with a single button press on the back of the camera, just below the LCD screen. Hold it for two seconds until you see the LED lights flash on the side — one light means it is in standby mode, ready to record. The camera will beep once when it powers up fully.

Before your first use, insert a microSD card into the slot on the right side of the camera (facing the back). The card should click into place. Without a memory card, the Hero 3 will power on but cannot record video or photos. You will also want to charge the battery using the included USB cable — a full charge takes about two hours and gives you roughly 90 minutes of recording time at 1080p resolution.

Once powered on, the camera defaults to video mode. The LCD screen on the back shows what the camera sees, along with recording time remaining, resolution, and frame rate. If the screen is off, press the power button once to wake it without powering down the camera.

Key Takeaways

  • Press and hold the back button for two seconds to power on; one LED light means the camera is ready to record.
  • Insert a microSD card before recording — the camera cannot save footage without one.
  • Video mode is the default setting; press the mode button on top to switch between video, photo, and burst modes.
  • Press the red record button on top to start and stop recording; the LED on the side blinks red while recording.
  • The LCD screen shows remaining battery and storage time, so check it before long sessions.

Switching Between Recording Modes

The Hero 3 has three main modes: video, photo, and burst. Press the mode button on the top left of the camera to cycle through them. The LCD screen displays which mode you are in — a video camera icon for video mode, a still camera icon for photo mode, and a burst icon for rapid-fire photos.

Video mode is what most users start with. In this mode, pressing the red record button on top begins recording when ready. The LED on the side blinks red, and a timer on the screen counts up. Press the record button again to stop.

Photo mode captures single still images. Press the record button once, and the camera takes one photo. The screen flashes briefly to confirm the shot was saved. Burst mode takes multiple photos in rapid succession — press and hold the record button, and the camera fires shots as fast as the frame rate allows (up to 30 frames per second depending on your settings). Release the button to stop.

Adjusting Resolution and Frame Rate

The Hero 3 shoots at different resolutions and frame rates depending on your needs and available storage. To change these settings, press the settings button (the wrench icon) on the back of the camera. Use the up and down arrows to navigate the menu, and press the settings button again to select an option.

Common video resolutions include 1080p at 30 or 60 frames per second, 720p at 60 frames per second, and 480p for longer recording times on smaller cards. Higher resolutions use more storage — 1080p at 30fps uses roughly 150 MB per minute, while 720p at 60fps uses about 200 MB per minute. If you are recording on a smaller card or have limited storage, lower resolutions let you record longer.

Frame rate affects how smooth motion looks. 60fps captures faster action more smoothly and is better for slow-motion playback later. 30fps is standard for most everyday recording and uses less storage. Once you select your resolution and frame rate, press the power button to exit the menu and return to recording mode.

Using the WiFi Remote and App Connection

The Hero 3 can connect to the GoPro App on your smartphone via WiFi, letting you control the camera remotely and preview footage on your phone. To enable WiFi, press the settings button, navigate to "Wireless", and select "On". The camera will display a WiFi network name and password on the LCD screen.

On your phone, open the GoPro App, go to settings, and select your Hero 3 from the list of available networks. Enter the password shown on the camera's screen. Once connected, you can see a live preview of what the camera sees, start and stop recording, and change basic settings without touching the camera itself.

WiFi drains the battery faster than normal recording, so turn it off when you are done using the remote. Press settings, navigate to Wireless, and select "Off".

Mounting and Positioning the Camera

The Hero 3 has a standard tripod mount on the bottom and comes with several mounting brackets — a helmet mount, chest mount, and adhesive mounts for flat surfaces. Screw the camera into whichever mount you need, making sure it is tight so the camera does not shift during recording.

The camera's field of view is very wide (about 170 degrees), so it captures much more than you see through the LCD screen. When mounting on a helmet or chest, angle the camera slightly downward so the horizon runs through the middle of the frame rather than at the top. This prevents the sky from dominating the shot.

Always check that your mount is find before recording. A loose mount can cause the camera to fall or shift mid-shot. If you are mounting on a moving vehicle or wearing it while active, test the mount while stationary first.

Playback and File Management

To watch footage you have recorded, press the settings button and select "Playback". Use the arrow buttons to scroll through your videos and photos. Press the settings button to play a selected video, and use the arrows to pause, rewind, or fast-forward. Press the power button to exit playback and return to recording mode.

The Hero 3 stores all files on the microSD card. To transfer footage to a computer, connect the camera to your computer using the included USB cable. The card will appear as a removable drive. Copy the DCIM folder (which contains all your videos and photos) to your computer, then eject the drive safely before disconnecting the camera.

If you need to delete files to free up space, press settings, select "Delete", and choose whether to delete a single file or all files. Be careful with this option — deleted files cannot be recovered.

Troubleshooting Common Issues

If the camera powers on but the LCD screen stays blank, the battery may be low. Charge it fully using the USB cable. If the screen is still blank after charging, try a hard reset by holding the power button for 10 seconds, then power on again.

If the camera powers on but will not record, check that a microSD card is inserted and has available space. The LCD screen shows how much recording time remains. If it says "0 min", the card is full — delete old files or insert a new card. Also check that the record button is actually being pressed; it requires a deliberate push.

If video is choppy or freezes during playback, the microSD card may be too slow. The Hero 3 works best with cards rated Class 10 or faster. Older or slower cards can cause dropped frames. If you experience this, try a newer, faster card.

If the WiFi connection drops frequently, move closer to the camera or reduce interference from other wireless devices. WiFi range is typically 30 feet in open space but shorter indoors or near other networks.

Frequently Asked Questions

How long does the battery last on a single charge?

A full charge provides roughly 90 minutes of continuous recording at 1080p resolution and 30 frames per second. Battery life varies based on resolution, frame rate, and whether WiFi is enabled. Higher resolutions and WiFi drain the battery faster. Cold temperatures also reduce battery life.

What size microSD card do I need?

A 32 GB card is a good starting point and holds about three to four hours of 1080p video. Larger cards (64 GB or more) let you record longer without swapping cards. Make sure the card is Class 10 rated for reliable performance with the Hero 3.

Can I record audio with the Hero 3?

Yes, the Hero 3 has a built-in microphone on the back of the camera. Audio is recorded automatically with all video. In windy conditions, the microphone picks up wind noise heavily. GoPro sells a wind-noise filter (called a "Mic Sock") that reduces this, but it is not included with the camera.

How do I know if the camera is actually recording?

The red LED on the side of the camera blinks continuously while recording. The LCD screen also shows a timer counting up. If the LED is not blinking red, the camera is not recording — check that you pressed the record button firmly.

What should I do if the camera gets wet?

The Hero 3 is water-resistant to 40 meters (130 feet) without a housing. If it gets wet, dry it with a soft cloth and let it air dry completely before powering on. Do not use it deeper than 40 meters or in saltwater without a protective housing, as water can damage the electronics.