Getting Your GoPro Hero 3 Ready to Record

The GoPro Hero 3 powers on with a single button press on the back of the camera. Hold the power button for two seconds until you see the LED lights flash and hear a beep. The camera will take another few seconds to fully boot — you'll see the GoPro logo appear on the small rear screen. Once the lights stop flashing and stay steady, the camera is ready to record.

Before your first use, charge the battery fully using the included USB cable. A dead battery won't power on at all, and the Hero 3 takes roughly two hours to charge from empty. The battery door is on the bottom of the camera; slide it open, insert the battery with the contacts facing toward the camera body, and close the door until it clicks.

Insert a microSD card into the slot on the side of the camera if you haven't already. The Hero 3 won't record video without one. The card should click into place when fully inserted. Format the card inside the camera itself by going to Settings > Format Card — this erases any existing data and prepares it for the Hero 3's file system.

Key Takeaways

  • Press and hold the power button on the back for two seconds to turn the camera on; the LED lights will flash and then steady once it's ready.
  • The Hero 3 records video by pressing the shutter button on top; press once to start, once to stop.
  • Use the mode button on the back to switch between video, photo, and burst modes before you start recording.
  • The rear screen shows battery level, recording time remaining, and current mode, so check it before you go out.
  • Turn the camera off by holding the power button for three seconds to save battery life when you're not recording.

Switching Between Recording Modes

The Hero 3 has three main recording modes: video, photo, and burst. Press the mode button on the back of the camera to cycle through them. The rear screen will display which mode you're in — a video camera icon means video mode, a still camera icon means photo mode, and a burst icon (multiple frames) means burst mode.

Video mode records continuous footage at your chosen resolution and frame rate. Photo mode captures a single still image each time you press the shutter button. Burst mode takes multiple photos in rapid succession — useful for action shots where you want to pick the sharpest frame later.

Change your video resolution and frame rate in the Settings menu. Press the settings button (the wrench icon) on the rear screen, navigate to Video Resolution, and choose from options like 1080p at 60 frames per second or 720p at 120 frames per second. Higher resolution uses more battery and fills your card faster, but gives you sharper footage. Higher frame rates are better for slow-motion playback.

Recording Video and Taking Photos

Once you've selected video mode and set your resolution, press the shutter button on top of the camera to start recording. A red dot will appear on the rear screen, and you'll hear a beep. The timer in the corner shows how long you've been recording. Press the shutter button again to stop — you'll hear another beep and the red dot disappears.

For photos, switch to photo mode using the mode button, then press the shutter button once. The camera will capture a single image and display it briefly on the rear screen. In burst mode, hold down the shutter button and the camera will fire multiple shots per second until you release it.

The rear screen shows your remaining battery life in the top left corner and how much space is left on your microSD card in the top right. If the battery icon turns red or the card shows a warning, you're running low on one or both. Stop recording and either charge the battery or swap in a fresh card.

Adjusting Settings and Playback

Access the settings menu by pressing the wrench icon button on the rear screen. From here you can adjust video resolution, frame rate, white balance, exposure, and field of view. Most users leave these at default settings, but if your footage looks too dark or too bright, try adjusting exposure up or down by one or two stops.

To play back video or photos you've recorded, press the play button (the triangle icon) on the rear screen. Use the left and right arrows to scroll through your files. Press the shutter button to select a file and watch it play. Press the mode button to return to the recording screen.

Delete unwanted files by selecting them in playback mode and pressing the delete button (trash icon). Deleted files cannot be recovered, so only remove footage you're certain you don't need. If you want to keep your files safe, transfer them to a computer using the USB cable before you delete anything from the card.

Powering Down and Extending Battery Life

Turn off the Hero 3 by holding the power button for three seconds. The LED lights will flash once and then go dark. The camera will shut down completely within a few seconds. Always power down when you're finished recording for the day — the Hero 3 draws power even when idle, and leaving it on will drain the battery.

Battery life depends on what you're recording. Continuous 1080p video at 60 frames per second will drain a full battery in roughly 90 minutes. Lower resolutions and frame rates extend battery life — 720p at 60 fps gets you closer to two hours. Recording in bursts rather than continuous video also saves power because the camera isn't running constantly.

If you're out in cold weather, battery life drops significantly. Bring a spare battery and keep it warm in an inside pocket until you need it. Fully charge both batteries before you leave home, and swap them out when the first one dies rather than waiting for a low-battery warning.

Connecting to WiFi and Transferring Files

The Hero 3 has built-in WiFi that lets you control the camera remotely using the GoPro app on a smartphone or tablet. Press the WiFi button on the side of the camera to turn WiFi on. The rear screen will display the WiFi network name and password. Open the GoPro app on your phone, select your camera from the list of networks, and enter the password shown on the camera screen.

Once connected, you can start and stop recording from your phone, change settings, and preview what the camera sees in real time. This is useful if you're mounting the camera somewhere you can't easily reach. WiFi drains the battery faster than recording alone, so turn it off when you don't need it by pressing the WiFi button again.

To transfer video and photos to your computer, connect the Hero 3 to your computer using the USB cable. The camera will appear as a removable drive. Open it and navigate to the DCIM folder, where all your video and photo files are stored. Copy the files to your computer's hard drive, then eject the camera safely before unplugging the cable.

Troubleshooting Common Issues

If the camera won't turn on, the battery is likely dead. Plug it in using the USB cable and let it charge for at least 30 minutes before trying again. If it still won't power on after charging, try removing the battery, waiting 10 seconds, and reinserting it.

If the camera turns on but won't record, check that a microSD card is inserted and that it has free space. If the card is full, delete old files or insert a new card. If the card is inserted but the camera still won't record, try formatting the card in the Settings menu — this erases everything on it but often fixes recording problems.

If the rear screen is black or won't display anything, the camera may be in a mode where the screen is off to save power. Press any button to wake it up. If the screen stays black, try powering the camera off and back on.

If video playback is choppy or stutters, your microSD card may be too slow. The Hero 3 works best with cards rated Class 10 or faster. Slower cards can cause playback issues even if recording works fine.

Frequently Asked Questions

How long does the battery last on a single charge?

A full battery lasts roughly 90 minutes of continuous 1080p video at 60 frames per second. Lower resolutions and frame rates extend this to two hours or more. Recording in short bursts rather than continuous video also stretches battery life. Cold weather reduces battery life by 20 to 30 percent.

Can I record while the camera is charging?

Yes, the Hero 3 can record while plugged into a USB power source. This is useful if you're recording for longer than a single battery charge allows. Use a USB power adapter rated for at least 1 amp of current to may support the camera charges while recording.

What microSD card should I buy?

Use a Class 10 microSD card rated for at least 30 megabytes per second write speed. Slower cards can cause choppy playback or dropped frames. Most 32 GB or 64 GB cards work well with the Hero 3 and cost between 15 and 30 dollars.

Why is my video blurry or out of focus?

The Hero 3 has a fixed-focus lens set for distances of about three feet and beyond. Anything closer than three feet will appear blurry. If your footage is blurry at normal distances, the lens may be dirty — wipe it gently with a soft cloth. If it's still blurry after cleaning, the camera may need service.

How do I delete all files at once instead of one by one?

The Hero 3 doesn't have a delete-all function in the camera menu. You must delete files individually using the playback screen, or connect the camera to a computer and delete files from the DCIM folder. Formatting the microSD card in Settings will erase everything at once, but this cannot be undone.