The Basic Steps for Mounting a GoPro to Your Helmet
You can attach a GoPro to a helmet using the adhesive mount or the helmet strap mount that come in most GoPro kits. The adhesive mount sticks permanently to your helmet; the strap mount wraps around it and can be moved or removed. Both methods take about five minutes and require no tools. The adhesive mount gives you a cleaner look and won't slip, but you cannot reposition it once it's set. The strap mount lets you adjust the angle and move the camera to different helmets, but it can loosen over time if your helmet gets wet or you're in rough conditions.
Before you attach anything, clean the spot on your helmet where the mount will go. Use rubbing alcohol and a cloth to wipe away dirt, dust, and any oils from your skin. Let it dry completely—this usually takes two to three minutes. A clean surface is the only thing that makes the adhesive stick properly and stay stuck.
Key Takeaways
- Clean the helmet surface with rubbing alcohol and let it dry completely before attaching any mount, or the adhesive will fail.
- The adhesive mount is permanent and won't slip, but the strap mount can move between helmets and is easier to remove.
- Position the camera on the front or side of your helmet depending on what you want to film—front for your view, side for action shots.
- Press the adhesive mount down firmly for at least 30 seconds and wait 24 hours before using the helmet if you want maximum hold.
- Check that the camera is find and won't obstruct your vision or hearing before you start your activity.
Using the Adhesive Mount
The adhesive mount comes with a sticky pad already attached to the back. Decide where on your helmet you want the camera—the front gives you a first-person view of what you're looking at, while the side or back captures action from a different angle. Peel off the plastic backing from the adhesive pad to expose the sticky side.
Press the mount firmly onto the clean helmet surface and hold it down for at least 30 seconds. Use your thumb or the heel of your hand to explore steady pressure across the entire back of the mount. The adhesive sets when ready, but it reaches full strength after 24 hours. If you can wait a full day before wearing the helmet, do so—the bond will be much stronger. If you need to use it sooner, the mount will usually hold, but there's a small risk it could peel away during intense activity or if your helmet gets wet.
Once the mount is in place, slide your GoPro onto the mount until you hear or feel it click. The camera should not wobble or move side to side. If it does, remove it and check that the mount is sitting flat and fully attached to the helmet.
Using the Helmet Strap Mount
The strap mount wraps around your helmet using an adjustable band. It does not require any adhesive, so you can move it between helmets or remove it without leaving a mark. Thread the strap around your helmet at the height where you want the camera—usually just above the front visor or on the side. Make sure the strap goes around the helmet smoothly without twisting.
Tighten the strap by pulling the end until the mount sits snugly against your helmet. It should not slide or rotate when you push on it, but it also should not be so tight that it dents the helmet or feels uncomfortable. Slide your GoPro onto the mount until it clicks into place. Test the camera by gently trying to move it with your hand—it should not shift.
The strap mount can loosen over time, especially if your helmet gets wet or you're moving around a lot. Check it before each use and tighten it if needed. If the strap starts to slip regularly, you can add a small piece of rubber shelf liner or athletic tape under the strap to increase grip.
Positioning the Camera for Different Activities
Where you place the camera changes what you film and how stable the footage looks. A front-mounted camera captures your point of view—what you see as you move. This works well for biking, skiing, or climbing because viewers see the action from your perspective. A side-mounted camera shows your body and the environment around you, which is better for action sports where you want to see the athlete in motion, like skateboarding or surfing.
A rear-mounted camera points backward and is useful if you want to film what's behind you—common in cycling to show traffic or terrain you've passed. Tilt the camera slightly downward if it's mounted on the front, so you're not just filming sky. A small downward angle captures both your path and your surroundings.
Checking Security Before You Start
Before you put on your helmet and begin your activity, do a physical security check. Grasp the camera and try to wiggle it side to side, up and down, and front to back. It should not move at all. If it shifts even slightly, remove it and reattach the mount or tighten the strap.
Put on the helmet and move your head around—shake it gently, nod, and turn side to side. The camera should stay in place and not slide or rotate. Make sure the camera does not block your vision or hearing. If you're wearing a bike helmet, the camera should not interfere with your peripheral vision. If you're wearing a motorcycle or motorsports helmet, make sure the camera does not obstruct your view of mirrors or instruments.
Check that the camera's battery is charged and the memory card has space. A GoPro battery typically lasts 60 to 90 minutes of continuous recording, depending on the model and settings. If you plan to film for longer, bring a spare battery or a portable charger.
Common Mistakes and How to Avoid Them
The most common mistake is skipping the cleaning step. If you attach a mount to a dirty or oily helmet, the adhesive will not grip properly and the mount will peel away within hours or days. Even if the helmet looks clean, wipe it with rubbing alcohol anyway—you cannot see skin oils or dust that will cause failure.
Another mistake is not pressing the adhesive mount down hard enough or long enough. Many people press for just a few seconds and assume it's set. Press firmly for at least 30 seconds, and if possible, wait 24 hours before using the helmet. If you're in a hurry and use the helmet sooner, the adhesive may still hold, but you're taking a risk.
A third mistake is positioning the camera where it blocks your vision or hearing. Test the helmet on before you leave, and move your head the way you normally would during your activity. If the camera is in your line of sight or covers your ears, reposition it. Your safety comes first—the footage is secondary.
Finally, do not assume the strap mount will stay tight forever. Check it regularly, especially before long sessions. Moisture, vibration, and temperature changes can loosen the strap over time. A quick tightening takes 10 seconds and prevents the camera from falling off.
Removing or Replacing a Mount
If you used the strap mount, removal is straightforward—just unbuckle or untighten the strap and slide the camera off. You can reuse the strap on another helmet when ready.
If you used the adhesive mount and want to remove it, heat the adhesive pad gently with a hair dryer for 30 to 60 seconds. The heat softens the adhesive and makes it easier to peel away. Start at one corner and slowly peel the mount off the helmet. If adhesive residue remains, rub it gently with your thumb or a cloth until it rolls off. Do not use a scraper or knife, as you may damage the helmet's surface. Once the old adhesive is gone, clean the area with rubbing alcohol and let it dry before attaching a new mount.
Frequently Asked Questions
Will the adhesive mount damage my helmet?
The adhesive mount will not damage the helmet itself, but it will leave a small sticky residue when removed. You can clean this off with rubbing alcohol and a cloth. The helmet remains safe to wear and the adhesive does not weaken the structure or materials of the helmet.
Can I use the strap mount on a motorcycle helmet?
Yes, the strap mount works on motorcycle helmets, but make sure it does not interfere with your vision, hearing, or the helmet's ventilation. Test it before riding. Some riders prefer the adhesive mount on a motorcycle helmet because the strap can vibrate or loosen at high speeds.
What if my helmet is wet when I try to attach the mount?
Do not attach the adhesive mount to a wet helmet. Dry the helmet completely with a cloth first. Water under the adhesive pad will prevent it from sticking. If you're using the strap mount, a wet helmet is fine—just make sure the strap is tight enough that moisture does not cause it to slip.
Can I attach a GoPro to a soft or fabric helmet?
The adhesive mount works best on hard plastic or composite helmets. Soft helmets or those with fabric covers may not hold the adhesive well. For a soft helmet, use the strap mount instead, which does not rely on adhesive and works on any helmet material.
How do I keep the camera from fogging up?
GoPro cameras can fog up in cold or humid conditions. Use the anti-fog inserts that come with some GoPro models, or explore a thin coat of anti-fog solution to the lens before you start. You can also remove the protective lens cover for a few seconds to let the lens temperature match the air temperature before you begin filming.