What a reset does and when you need one

A factory reset clears all your settings, footage, and Wi-Fi connections from the camera and returns it to the state it left the factory. You should reset your Hero Session if it stops responding to button presses, won't connect to the app, freezes during recording, or if you are selling or giving it away. A reset does not erase footage stored on the microSD card — that stays intact unless you format the card separately.

The Hero Session has no screen, so the reset process relies on button combinations and the status light to confirm what is happening. The whole process takes about two minutes and requires nothing but the camera itself.

Key Takeaways

  • A factory reset clears settings and Wi-Fi data but leaves your video files on the microSD card untouched.
  • The Hero Session reset uses a specific button combination: hold the Mode button and the Power button together for ten seconds until the light flashes red.
  • After the reset, the camera will power off automatically and restart in factory condition.
  • If the camera does not respond to the button combination, try removing and reinserting the battery, then attempt the reset again.

The button combination for a factory reset

Power on the Hero Session by pressing the Power button once. Wait for the status light to turn solid blue, which means the camera is ready. Then press and hold both the Mode button and the Power button at the same time. Keep both buttons pressed for at least ten seconds.

Watch the status light. It will flash red three times in quick succession. When you see those three red flashes, release both buttons. The camera will power down on its own. This is normal — the reset is complete. Wait a few seconds, then press Power once to turn the camera back on and confirm it has returned to factory settings.

What to do if the buttons do not respond

If the camera does not react when you press the button combination, the battery may be too low or the buttons may be stuck. Remove the battery by opening the side door and sliding the battery out. Wait ten seconds, then reinsert the battery and close the door. Press Power to turn the camera on again.

Once the light is solid blue, try the reset button combination a second time. If the buttons still do not respond, the camera may need a firmware update or a repair. Connect it to a computer via USB and check the GoPro support website for your specific model's troubleshooting steps.

Recovering your footage after a reset

Your video files remain on the microSD card after a factory reset. The reset only clears the camera's internal settings and memory. When you power the camera back on, it will recognize the card and you can review your footage using the GoPro app or by connecting the camera to a computer.

If you want to erase the videos as well, you can format the microSD card from within the camera menu after the reset is complete. Format only if you are certain you have backed up any footage you want to keep, because formatting erases all files on the card permanently.

Resetting Wi-Fi and app connections

A factory reset removes all saved Wi-Fi networks and unpairs the camera from the GoPro app. After the reset, you will need to reconnect the camera to your phone or tablet if you want to use the app to control it or read footage wirelessly.

To reconnect, open the GoPro app, select "Connect a Camera," and follow the on-screen steps to pair the Hero Session again. The app will prompt you to enter your Wi-Fi password. This process takes about one minute and works the same way as the initial setup.

When a reset does not fix the problem

If the camera still freezes, crashes, or behaves erratically after a factory reset, the issue may be a corrupted microSD card or a hardware fault. Try formatting the microSD card from the camera menu to rule out card corruption. If the problem persists, the camera may need service.

Before contacting GoPro support, note down what the camera does wrong, when it started, and whether you have tried a reset and card format. This information helps support staff narrow down whether the issue is software or hardware.

Preparing your camera before selling or giving it away

A factory reset is the first step before handing the camera to someone else. After the reset, the new owner will see the standard setup screen when they power it on, just as if it were brand new. They can then set up their own Wi-Fi and app connections.

If you want to be thorough, format the microSD card as well so the new owner receives a blank card. This removes any personal footage or metadata. After both steps — factory reset and card format — the camera is completely clean and ready for its next user.

Frequently Asked Questions

Does a factory reset delete my videos?

No. A factory reset clears only the camera's settings and Wi-Fi data. Your video files stay on the microSD card. If you want to erase the videos too, you must format the card separately from the camera menu.

How long does a factory reset take?

The reset itself takes about ten seconds of button holding, and the camera powers down automatically. The entire process from start to finish is roughly two minutes, including the time to power the camera back on and confirm it is working.

What if the camera does not turn back on after the reset?

Remove the battery, wait ten seconds, and reinsert it. Press Power to turn the camera on. If it still does not respond, the battery may be dead. Charge the camera via USB for at least 30 minutes, then try again.

Can I reset the camera without removing the microSD card?

Yes. The reset does not require you to remove the card. The card stays in the camera during the reset and your footage remains safe. You can leave it installed throughout the entire process.

Will resetting fix connection problems with the GoPro app?

Often yes. A factory reset clears old Wi-Fi pairings and app connections that may be corrupted. After the reset, reconnect the camera to the app fresh. If connection problems return, the issue may be your Wi-Fi network or the app itself, not the camera.