Reset Your GoPro Hero 3 Using the Camera Menu

The simplest way to reset your GoPro Hero 3 to factory settings is through the on-camera menu. Power on the camera, press the Menu button (the left button on the back), and navigate to Settings. Scroll down until you see Reset or Factory Reset—the exact wording depends on your firmware version. Select it, confirm the action when prompted, and the camera will restart with all original settings restored.

This method takes about two minutes and does not require a computer. Your video files and photos remain on the memory card; a factory reset only clears settings like resolution, frame rate, field of view, and any custom configurations you created.

Key Takeaways

  • Access the factory reset through the camera's Menu button, then navigate to Settings and select Reset.
  • A factory reset clears all settings but leaves your video and photo files intact on the memory card.
  • If the camera is frozen or unresponsive, hold the Power button for 10 seconds to force a shutdown, then try the menu reset.
  • After a reset, you may need to reformat the memory card in the camera to may support it works properly with the restored settings.
  • If the menu method fails, connect the camera to a computer and use GoPro's official firmware update tool as a last resort.

Force Shutdown When the Camera Is Frozen

If your Hero 3 is unresponsive or stuck on a screen, you cannot access the menu to reset. In this case, hold down the Power button on the back of the camera for 10 seconds until the screen goes black and the camera shuts down completely. Wait 30 seconds, then power it back on and try the menu reset again.

A force shutdown does not erase settings or files—it straightforward forces the camera to turn off when normal buttons do not work. This step often clears temporary glitches that prevent the menu from responding.

Reformat the Memory Card After Reset

After you complete a factory reset, the camera may behave unpredictably with an older memory card, especially if the card was used before the reset. To avoid recording errors or missing footage, reformat the card inside the camera itself. Power on the camera, go to Menu, find Format or Format Card in Settings, and confirm.

Formatting erases all files on the card, so transfer any videos or photos to a computer first. A freshly formatted card and factory reset settings work together to give you a clean starting point.

Update Firmware as an Alternative to Manual Reset

If the menu reset does not work or the camera still behaves strangely afterward, updating the firmware can restore the camera to a known working state. Visit the official GoPro website, read the latest Hero 3 firmware file, and follow their instructions to load it onto a memory card. Insert the card into the camera, go to Menu, find Firmware Update, and let the camera complete the process—do not turn it off during this time.

A firmware update takes 5 to 10 minutes and requires a fully charged battery. This method is more thorough than a menu reset because it replaces the camera's operating system itself, not just the settings.

What Happens to Your Files During a Reset

A factory reset returns the camera to the state it left the factory, but it does not touch your video files, photos, or any other data on the memory card. All your recorded content stays exactly where it is. The reset only affects the camera's internal settings: resolution, frame rate, white balance, protune mode, and any other preferences you changed.

If you want to erase files as well, you must delete them manually before or after the reset. Use the camera's Delete menu to remove individual files, or format the card (as described above) to wipe everything at once.

Troubleshooting a Reset That Does Not Stick

Occasionally the Hero 3 will reset but then revert to old settings after you power it off and back on. This usually means the memory card has corrupted data that interferes with the reset. The solution is to format the card as described in the "Reformat the Memory Card After Reset" section above, then perform the factory reset again.

If settings still do not stick after reformatting, try a firmware update. If the camera continues to malfunction even after a firmware update and card reformat, the camera's internal storage may be failing, and you may need to contact GoPro support or consider repair options.

Frequently Asked Questions

Will a factory reset erase my videos and photos?

No. A factory reset only clears the camera's settings—resolution, frame rate, white balance, and other preferences. All your video files and photos remain on the memory card. If you want to erase files, you must delete them separately using the camera's Delete menu or by formatting the card.

How long does a factory reset take?

A factory reset through the menu takes about one to two minutes. The camera will restart automatically once the reset is complete. A firmware update takes longer—usually 5 to 10 minutes—and requires a fully charged battery.

What should I do if the Menu button does not work?

If the camera is unresponsive, hold the Power button for 10 seconds to force a shutdown. Wait 30 seconds, power it back on, and try the menu again. If the buttons still do not respond, try a firmware update using a computer and the official GoPro firmware tool.

Do I need a computer to reset my Hero 3?

No. You can reset the camera using only the on-camera menu and buttons. A computer is only needed if the menu method fails and you want to try a firmware update as a last resort.

Should I format the memory card before or after the factory reset?

Format the card after the reset. This ensures the camera's fresh settings are applied to a clean card, which reduces the chance of recording errors. Always transfer your videos and photos to a computer before formatting, since formatting erases everything on the card.