Reset a GoPro Session in Three Steps

A factory reset clears all your settings, footage, and preferences and returns the camera to its original state. You do this through the camera's menu, not through a computer. Power on the Session, swipe down from the top of the screen to open the menu, select Preferences, then Reset, then Reset Camera. The camera will restart and show the startup wizard — this takes about two minutes.

A reset is useful when the camera freezes, won't connect to the app, or behaves unpredictably. It is also the step to take before selling or giving away the device, since it removes all your personal footage and settings. The Session will not lose its firmware version during a reset — the internal software stays current.

Before you reset, back up any footage you want to keep. The reset erases everything on the memory card. Connect the Session to a computer via USB cable, drag the DCIM folder to your hard drive, then proceed with the reset.

Key Takeaways

  • A factory reset is done through the camera menu by selecting Preferences, then Reset, then Reset Camera.
  • The reset erases all footage, photos, and custom settings from the memory card and returns the camera to factory defaults.
  • You should copy your video files to a computer before resetting if you want to keep them.
  • A reset takes about two minutes and the camera will restart and show the startup wizard when it is complete.
  • Resetting does not change the camera's firmware or require a computer — it is a self-contained operation on the device itself.

When to Reset Your Session

Reset the camera if it freezes during recording, refuses to power off normally, or stops responding to button presses. A frozen Session often recovers after a reset without any loss of footage — the reset clears the memory cache that caused the freeze, not the video files themselves, unless you explicitly choose to erase the card during the reset process.

If the Session won't connect to the GoPro app on your phone, a reset can fix the pairing issue. The app communicates with the camera over Wi-Fi, and a reset clears the stored Wi-Fi credentials and reconnection history. After the reset, you will pair the camera and app fresh, which often resolves connection problems that persisted through straightforward power cycles.

You should also reset before selling, trading in, or giving the camera to someone else. This removes all your video content, photos, and personal settings so the next owner starts with a clean device.

Back Up Your Footage Before Resetting

Connect the Session to a computer using the USB cable that came in the box. The camera will appear as a removable drive on your computer — on Windows it shows up in File Explorer, and on Mac it appears on the desktop. Open the DCIM folder, which holds all your video and photo files, and drag it to a folder on your hard drive. This copy process takes a few minutes depending on how much footage is on the card.

If you have a large amount of footage, use an external hard drive or cloud storage service to hold the files. Copying to the cloud through a service like Google Drive or Dropbox works, but it is slower than a direct USB transfer — a two-hour video file can take 10 to 20 minutes to upload depending on your internet speed.

Once the files are safely on your computer, you can proceed with the reset. The Session will erase everything on the memory card, so confirm the backup is complete before you start.

What Happens During and After a Reset

When you select Reset Camera from the menu, the Session will display a confirmation message asking if you are sure. Confirm the action, and the camera will power down and restart. During the restart, the camera clears the memory card and resets all settings to factory defaults — this takes about 90 seconds to two minutes.

After the restart, the camera will show the startup wizard, the same screen you saw when the Session was brand new. You will be asked to select your language, set the date and time, and choose your video resolution and frame rate. Complete these steps, and the camera is ready to use.

The Session will retain its firmware version — the internal software that runs the camera does not change during a reset. If a firmware update is available, you will see a notification in the menu, but a reset does not install updates or remove them.

Soft Reset vs. Factory Reset

A soft reset is a straightforward power cycle: hold the power button until the camera shuts down, wait five seconds, then power it back on. This clears temporary glitches and memory cache without erasing any footage or settings. Use a soft reset first if the camera is frozen or unresponsive — it fixes most minor problems and takes less than a minute.

A factory reset is the full reset described above. It erases everything and returns the camera to its original state. Use a factory reset only if a soft reset did not fix the problem, or if you are preparing the camera for someone else to use.

If the Session will not power on at all, a soft reset will not help. In that case, charge the battery fully using the USB cable, wait 30 minutes, then try powering on again. If the camera still will not start, the battery may be depleted beyond recovery, and you may need to contact GoPro support.

Troubleshooting After a Reset

If the Session still freezes or behaves erratically after a factory reset, the problem may be the memory card itself. Try formatting a different microSD card in the camera — insert the new card, go to Preferences, select Reset, then Format Card. If the camera works normally with a different card, the original card is failing and should be replaced.

If the camera still will not connect to the app after a reset, make sure your phone and the Session are both on the same Wi-Fi network. Open the GoPro app, select your camera from the list of available devices, and enter the Wi-Fi password shown on the camera screen. If the app still cannot find the camera, restart both devices and try again.

If the Session will not turn on after a reset, plug it into a computer using the USB cable and let it charge for at least one hour. A reset can drain the battery, and the camera may not power on until it has enough charge. After charging, press the power button and hold it for three seconds.

Memory Card Compatibility and Formatting

The GoPro Session works with microSD cards up to 128 GB, though GoPro recommends cards rated Class 10 or UHS-I for reliable recording. Before using a new card in the Session, format it in the camera itself — do not format it on a computer. Insert the card, go to Preferences, select Reset, then Format Card. This ensures the card is set up correctly for the camera's file system.

Formatting a card in the camera erases all files on that card. If you have footage on the card you want to keep, back it up to a computer first. After formatting, the card is ready to record, and the Session will recognize it when ready.

If you use the same card in multiple cameras or devices, format it in the Session each time you switch to it. This prevents compatibility issues and file corruption that can happen when a card is formatted for a different device.

Frequently Asked Questions

Does a factory reset delete my videos?

Yes, a factory reset erases all video files, photos, and settings from the memory card. Back up your footage to a computer before you reset. If you have already reset and lost footage, professional data recovery services may be able to recover files, but this is expensive and not always successful.

Can I reset the Session without a computer?

Yes, the reset is done entirely on the camera through the menu. You do not need a computer to reset. You only need a computer if you want to back up your footage before resetting.

How long does a factory reset take?

A factory reset takes about two minutes from start to finish. The camera will power down, clear the memory card, restart, and show the startup wizard. Do not turn off the camera during this process.

Will a reset fix a camera that won't record?

A reset may fix recording problems caused by software glitches or corrupted settings. Try a soft reset first — power the camera off and back on. If that does not work, try a factory reset. If the camera still will not record after a reset, the problem may be the memory card or internal hardware, and you should contact GoPro support.

What should I do if the reset menu option is grayed out?

If the Reset option is not clickable, the camera battery may be too low. Charge the Session fully using the USB cable, then try again. If the option is still grayed out after charging, try a soft reset by powering the camera off and back on, then check the menu again.