The quickest way to restart your GoPro Hero 3

The simplest restart is to hold the power button (the button on top of the camera) for three seconds until the camera powers off completely. Wait five seconds, then press the power button again for three seconds to turn it back on. This soft restart clears the camera's memory and stops most freezing or lag without erasing your footage.

If the camera is frozen and won't respond to the power button, you can force a restart by removing the battery. Open the battery door on the side of the camera, slide out the battery, and wait 30 seconds. Reinsert the battery and press the power button. This hard restart works when the software has locked up completely.

Most restart problems happen because the camera's processor is overloaded—usually from recording in high resolution, using WiFi, or running the camera in very cold conditions. A restart clears temporary files and gives the processor a fresh start.

Key Takeaways

  • A soft restart (power button for three seconds, wait, power on again) fixes most freezing and lag without losing footage.
  • A hard restart (remove the battery for 30 seconds, reinsert, power on) works when the camera is completely frozen and won't respond to buttons.
  • Freezing usually happens during high-resolution recording, WiFi use, or in cold weather, and a restart clears the processor.
  • If the camera restarts but when ready freezes again, the SD card may be corrupted and needs to be reformatted in the camera itself.

When to use a soft restart versus a hard restart

Use a soft restart first. It is gentler on the camera's components and takes only seconds. Press and hold the power button for three seconds until you see the screen go black and hear the shutdown tone. Count to five, then press the power button again for three seconds. The camera will boot up normally, and all your settings and footage remain untouched.

Use a hard restart only if the soft restart does not work or if the camera is completely unresponsive. A hard restart forces the camera to shut down without going through its normal shutdown sequence, which is why you should only do it when necessary. After you remove the battery, wait the full 30 seconds before reinserting it—this gives the camera's capacitors time to fully discharge.

If you restart the camera and it freezes again within a few minutes, the problem is likely not a temporary glitch. Move to the SD card troubleshooting steps below.

Restarting when the camera is frozen or unresponsive

If the screen is black or stuck on one image and buttons do not work, the camera's processor has locked up. Start with a soft restart: hold the power button for a full three seconds even if nothing seems to happen. Sometimes the camera is frozen but still receiving input. If the screen stays black or frozen after 10 seconds, move to a hard restart.

For a hard restart, open the battery door (on the right side of the camera when facing the lens). Slide the battery out toward the back of the camera. You will see a small metal contact strip—do not touch it. Wait 30 seconds. This pause is important because it allows residual power to drain from the camera's circuits. Slide the battery back in until you hear a click, close the battery door, and press the power button.

The camera should power on and show the GoPro logo. If it powers on but when ready freezes again, the SD card is likely corrupted. Proceed to the SD card section below.

Checking and reformatting the SD card

If the camera restarts but freezes during normal use, the SD card may have corrupted files. The Hero 3 can become unstable when the card has bad sectors or incomplete video files from a previous crash.

The safest way to fix this is to reformat the SD card inside the camera itself. Power on the camera, press the Menu button (the button on the back left), navigate to Setup, then scroll to Format SD Card. Select it and confirm. The camera will erase everything on the card and prepare it for use. This takes about one minute.

Reformatting erases all footage on the card, so copy any videos or photos to a computer first if you want to keep them. After reformatting, the camera should run smoothly. If it freezes again after a reformat, the SD card itself may be failing and should be replaced.

Restarting after a firmware update

If you recently updated the Hero 3's firmware (the camera's internal software), a restart is often necessary to complete the update. The camera may feel slow or unresponsive until the restart finishes.

After a firmware update, perform a soft restart: hold the power button for three seconds, wait five seconds, and power on again. The camera may take longer than usual to boot up—this is normal. Let it sit for up to one minute before pressing any buttons. Once the home screen appears, the update is complete.

If the camera will not power on after a firmware update, the battery may have drained during the update process. Plug the camera into a USB charger for 30 minutes, then try powering on again.

Preventing freezes and reducing restart needs

The Hero 3 freezes most often when the processor is working too hard. High-resolution recording (1080p at 60 frames per second or 4K at any frame rate) uses most of the camera's processing power. If you are experiencing frequent freezes, try recording at 1080p at 30 frames per second instead, which is still high quality but uses less processor power.

WiFi and Bluetooth drain the processor as well. If you do not need to control the camera remotely or transfer footage wirelessly, turn off WiFi in the camera's settings. This alone often stops freezing during recording.

Cold weather slows the camera's processor. If you are filming in temperatures below 40°F, the camera may freeze or shut down unexpectedly. Keep the camera in an inside pocket or warm bag between shots, and give it time to warm up before recording again.

Finally, use a fast SD card rated for video recording. The Hero 3 works best with cards rated Class 10 or UHS-I. Older or slower cards can cause the camera to freeze when writing large video files.

When to contact GoPro support

If the camera restarts successfully but freezes during every recording session, or if it will not power on even after a hard restart and battery charge, the hardware may be failing. Contact GoPro support with the camera's serial number (found under the battery) and a description of when the freezing started.

GoPro support can determine whether the issue is a software problem that a firmware reinstall can fix, or a hardware failure that requires repair or replacement. Keep your proof of purchase handy—the Hero 3 may still be under warranty depending on when you bought it.

Frequently Asked Questions

Will restarting the camera delete my videos?

A soft restart will not delete anything. A hard restart (removing the battery) also will not delete footage. Only reformatting the SD card erases files, and the camera warns you before doing that. Always copy important footage to a computer before reformatting.

How long does a restart take?

A soft restart takes about 10 to 15 seconds from power-off to the home screen. A hard restart takes about 20 seconds because the camera needs time to fully discharge before the battery goes back in. Firmware updates can take up to two minutes to complete after a restart.

What if the camera powers on but the screen is blank?

The camera may be in a low-power mode or the display may be off. Press the power button once more to wake the display. If the screen stays blank, try a hard restart. If it remains blank after a hard restart, the LCD may have failed and the camera should be sent to GoPro support.

Can I restart the camera while it is recording?

No. Restarting while recording can corrupt the video file. Always stop recording first by pressing the shutter button, wait for the recording light to turn off, then restart the camera.

Why does my camera freeze only when I use WiFi?

WiFi uses significant processor power on the Hero 3. If freezing happens only during WiFi use, turn off WiFi when you do not need remote control or live preview. This frees up processor resources for video recording and should stop the freezing.