Open the case by releasing the side latch and lifting the back door
Your GoPro sits inside a waterproof case held shut by a single side latch—a small lever on the left edge of the case when you're looking at the front. Push this latch away from the case (toward the back) until it clicks and releases. The back door of the case will then swing open on its hinge.
Do not force the latch. If it does not move smoothly, you may be pushing in the wrong direction. The latch should move away from the camera body, not toward it. Once released, the back door swings open freely, and you can see the camera mounted on its frame inside.
Key Takeaways
- The side latch on the left edge of the case must be pushed away from the camera body to release the back door.
- The camera is mounted on a frame that slides out of the case once the back door is open.
- Pull the frame straight out toward you; do not twist or angle it, as this can catch on the case edges.
- Check that the rubber gasket around the back door is clean and dry before closing the case again.
- If the frame feels stuck, look for water droplets or debris along the edges and gently wipe them away.
Slide the camera frame straight out of the case
Once the back door is open, you will see the camera mounted on a plastic frame that sits inside the case. Grip the frame on both sides and pull it straight toward you in one smooth motion. The frame should slide out without resistance. Do not twist the frame side to side or angle it upward—this can catch the edges on the case walls and make removal harder.
If the frame feels stuck, stop and look along the edges where the frame meets the case. You may see water droplets, sand, or a small piece of debris blocking the path. Wipe the edges dry with a soft cloth and try again. The frame should come out cleanly once the path is clear.
Detach the camera from the frame if needed
The camera itself is held to the frame by a single thumbscrew at the bottom. If you need to remove the camera completely from the frame, rotate this thumbscrew counterclockwise by hand until it is loose enough to lift away. You do not need tools—your thumb and fingers are enough. Once the screw is loose, the camera lifts straight up and off the frame.
Most of the time you do not need to separate the camera from the frame. Leaving them together makes reassembly faster and reduces the chance of losing small parts. Only remove the camera if you are replacing the frame, cleaning the mounting point, or storing the camera separately.
Check the gasket and case interior before closing
Before you put the case back together, take a moment to inspect the rubber gasket that runs around the back door. This gasket keeps water out, so it must be clean and dry. Look for sand, salt residue, hair, or water droplets along the entire seal. Wipe the gasket gently with a soft, dry cloth if you see any debris.
Also check the interior walls of the case where the frame slides. If you see water, sand, or salt buildup, wipe these areas dry as well. A case that looks clean on the outside can trap moisture inside, which corrodes the camera over time. Taking 30 seconds to dry the interior now prevents problems later.
Reassemble the case by sliding the frame back in and closing the door
To put the camera back in the case, reverse the steps. Slide the frame straight into the case until it sits flush against the back. The frame should slide in as smoothly as it came out. Once the frame is fully seated, swing the back door closed and push the side latch toward the front of the case until it clicks into place. You will hear and feel a distinct click when the latch locks.
Test the latch by gently trying to open the back door. It should not budge. If the door opens easily, the latch did not fully engage. Release it and try again, pushing the latch all the way until you hear the click. A properly sealed case is essential for waterproofing, so take the extra second to confirm the latch is fully locked.
Avoid these common mistakes when removing the camera
The most common error is twisting or angling the frame as you pull it out. This catches the corners on the case walls and makes the frame feel stuck when it is actually just misaligned. Always pull straight out, parallel to the ground. If you feel resistance, stop, check the alignment, and try again rather than forcing it.
Another mistake is reassembling the case with a wet or dirty gasket. Water trapped under the seal can freeze in cold weather, warp the gasket, or allow moisture to seep into the camera. Spend 10 seconds wiping the gasket dry every time you open the case. The third common error is not fully engaging the side latch when closing. A latch that looks closed but is not fully clicked will let water in during use. Always listen for the click and test the door before you trust the seal.
Frequently Asked Questions
What if the side latch is stuck and will not move?
Stop pushing and check for salt buildup or sand around the latch mechanism. Rinse the latch area with fresh water and dry it completely. If the latch still will not budge, do not force it—you risk breaking the plastic. Let the case sit in the sun for an hour to dry thoroughly, then try again.
Can I open the case while it is underwater?
No. The case is designed to stay sealed while submerged. Opening it underwater will flood the camera. Always surface and move to dry land before opening the case. If you need to change settings or stop recording, do so before you enter the water.
Is the frame supposed to be tight inside the case?
The frame should slide smoothly with light resistance, not be loose or rattle. If it moves freely with no resistance, the gasket may be worn and the case may not seal properly. If it is very tight and hard to remove, the gasket may be swollen from heat or moisture. Either way, inspect the gasket for damage.
Do I need to remove the camera every time I use it?
No. You can leave the camera mounted on the frame inside the case for storage and transport. Remove the camera only when you need to charge it, clean the lens, or replace the frame. Keeping the camera in the case during storage protects it from dust and damage.
What should I do if water gets inside the case?
Remove the camera when ready and dry it with a soft cloth. Do not turn it on. Let it air-dry for at least 24 hours in a warm, dry place before powering it up. Inspect the gasket for cracks or tears. If the gasket is damaged, replace it before using the case again.