Turn on the camera and insert the battery and memory card first
The GoPro Hero 3 powers on with the button on the right side of the camera body. Before you press it, you need a charged battery in the slot on the bottom and a microSD card (not full-size SD) in the slot on the side. The camera will not record without both.
The battery charges inside the camera using the USB cable that came in the box, or you can remove it and charge it separately in an external charger. A full charge takes roughly two hours. The microSD card should be at least Class 10 speed — this matters because the Hero 3 records at high bitrate and a slow card will cause dropped frames and corrupted video.
When you first power on the camera, it will ask you to set the date and time using the buttons on the back. Get this right, because the timestamp is burned into your footage and you cannot change it later.
Key Takeaways
- Insert a charged battery and Class 10 microSD card before powering on, or the camera will not record.
- Press the shutter button on top to start and stop recording; the red light on the front tells you when video is actively recording.
- The Hero 3 has three modes — Video, Photo, and Burst — selected by holding the mode button on the back until the screen shows your choice.
- Video resolution and frame rate are set in the menu accessed by pressing the power button while the camera is on; 1080p at 30 fps is the most common choice for balance between quality and file size.
- Transfer footage to a computer by connecting the camera to a USB port, or remove the microSD card and use a card reader.
Record video by pressing the shutter button on top
The large button on the top of the camera is your shutter. Press it once to start recording. The red LED on the front of the camera will light up solid, and you will see a timer counting up on the back screen. Press the shutter button again to stop recording.
The Hero 3 will record continuously until your memory card is full or your battery dies. There is no limit to clip length — if you hold the shutter down for an hour, you get one hour-long file. Most users break their footage into shorter clips by stopping and restarting manually, which also makes editing easier later.
The camera records in the resolution and frame rate you set in the menu. If you have not changed the defaults, it will record at 1080p (1920 × 1080 pixels) at 30 frames per second. At this setting, one hour of video takes roughly 1.5 gigabytes of space on your card.
Switch between Video, Photo, and Burst mode using the mode button
Hold down the mode button on the back left of the camera for two seconds. The screen will cycle through three options: a video camera icon (Video mode), a still camera icon (Photo mode), and a burst icon (Burst mode). Release the button when you see the mode you want.
In Video mode, the shutter button records moving footage. In Photo mode, each press of the shutter captures a single still image. In Burst mode, holding the shutter button takes multiple photos in rapid succession — useful for action shots where you want to pick the best frame later.
The mode you select stays active until you change it again. If you power off the camera and power it back on, it returns to Video mode regardless of what you had selected.
Adjust video resolution and frame rate in the menu
Press the power button while the camera is already on (not to turn it on, but while it is running). This opens the menu. Use the up and down arrow buttons to scroll to "Video Resolution" or "Frame Rate" and press the shutter button to select.
The Hero 3 offers several resolution options: 1080p (1920 × 1080), 960p (1280 × 960), 720p (1280 × 720), and WVGA (848 × 480). Higher resolution means larger file sizes and more detail, but also more strain on your battery and memory card. For most users, 1080p at 30 fps is the standard choice.
Frame rate options are 30 fps (standard, smooth motion), 60 fps (twice as much data, used for slow-motion playback), and 120 fps (extreme slow-motion, only available at lower resolutions). Higher frame rates use more battery and storage but give you more flexibility in editing. If you are not sure, stick with 30 fps.
Mount the camera using the included housing and accessories
The Hero 3 comes in a waterproof housing that protects it to 131 feet underwater. To insert the camera, open the latch on the back of the housing, slide the camera in lens-first, and close the latch until it clicks. The housing has a lens cover that you must remove before recording.
The housing has a standard tripod socket on the bottom (the same thread used on most camera tripods). You can also attach the camera to helmets, chest mounts, or pole mounts using the adhesive pads and quick-release buckles in the accessory kit. Clean the surface where you are mounting with rubbing alcohol and let it dry completely before explore the adhesive pad, or it will not stick.
If you are recording in dry conditions and do not need waterproofing, you can remove the camera from the housing and use it bare. The camera itself is not waterproof without the housing, so do not submerge it.
Transfer video files to your computer
Connect the camera to your computer using the USB cable that came in the box. Plug the USB end into a port on your computer and the small connector into the port on the bottom of the camera. The camera will appear as a removable drive on your computer, and you can drag the video files to a folder on your hard drive.
Video files are stored in a folder called DCIM on the memory card. Each video is named with a number (like GH010001.MP4). The files are in MP4 format, which works with most video editing software including iMovie, Adobe Premiere, and DaVinci Resolve.
Alternatively, you can remove the microSD card from the camera and insert it into a card reader connected to your computer. This is faster than transferring through USB and does not drain the camera battery. Card readers are inexpensive and widely available.
Manage battery life and prevent overheating
The Hero 3 battery lasts roughly 60 to 90 minutes of continuous recording at 1080p, depending on temperature and which features you have enabled. Cold weather drains the battery faster. If you are filming in winter or at high altitude, carry a spare battery.
The camera can overheat if you record for extended periods in hot weather or direct sunlight. If the back screen shows a thermometer icon, the camera has reached its temperature limit and will stop recording. Let it cool for 10 to 15 minutes before resuming. This is normal and does not mean the camera is broken.
To extend battery life, turn off the Wi-Fi feature (accessed in the menu) if you are not using it to control the camera remotely. Wi-Fi drains the battery even when you are not actively using it. You can also reduce screen brightness in the menu to save power.
Frequently Asked Questions
What size microSD card do I need?
A 32 GB card is the practical minimum for the Hero 3 and holds roughly 5 hours of 1080p video at 30 fps. Larger cards (64 GB or higher) are available and cost only slightly more. Make sure the card is Class 10 speed or faster, or you will experience dropped frames and corrupted files.
Can I use the camera while it is charging?
No. The Hero 3 must be powered off to charge the battery. You can charge the battery separately using an external charger if you want to keep filming with a second battery, but you cannot charge and record at the same time.
How do I delete video files from the camera?
Press the power button to open the menu, scroll to "Delete" using the arrow buttons, and press the shutter button. You can delete individual files or format the entire card (which erases everything). Formatting is faster if you want to clear the card completely.
What is the difference between the Hero 3 White and Black editions?
The Hero 3 Black records at higher frame rates and resolution than the White edition. The Black can shoot 1080p at 60 fps and 4K at 15 fps, while the White maxes out at 1080p at 30 fps. The Black also has a larger sensor and better low-light performance. Both use the same battery, housing, and accessories.
Can I control the camera remotely with my phone?
Yes, if you enable Wi-Fi in the menu. The GoPro App (available for iOS and Android) lets you view the live feed from the camera, start and stop recording, and change settings from your phone. The Wi-Fi range is roughly 100 feet in open space, but walls and interference reduce this significantly.