GoPro Hero 4 is waterproof to 40 meters without a housing

The GoPro Hero 4 has a waterproof rating of 40 meters (131 feet) straight out of the box. You do not need to buy a separate waterproof case to use it in shallow water, snorkeling, or light rain. The camera's body is sealed against water intrusion at that depth.

This rating applies to both the Hero 4 Black and Hero 4 Silver models. The sealing works because the camera has no removable battery door or memory card slot on the outside — all internal components are protected by gaskets and sealed compartments. As long as you have not opened the camera or damaged the seals, it will survive submersion to 40 meters.

The 40-meter depth limit is the maximum safe operating depth. Going deeper than that risks water entering the camera and destroying the electronics inside. If you plan to dive deeper than 40 meters, you will need to use the optional Super Suit housing, which extends the waterproof rating to 60 meters.

Key Takeaways

  • The GoPro Hero 4 is waterproof to 40 meters without any additional case or housing.
  • Do not submerge the camera deeper than 40 meters, as water pressure will exceed the seal's design limit.
  • The Super Suit housing extends waterproof protection to 60 meters if you need to film at greater depths.
  • Damage to the camera body, cracks in the lens, or opened compartments will compromise waterproofing at any depth.

What the 40-meter rating actually means

A 40-meter waterproof rating does not mean the camera can sit at 40 meters indefinitely. The rating is based on static water pressure tests — the camera is submerged at that depth for a set period under controlled conditions. In real use, factors like wave action, currents, and movement can stress the seals differently than a lab test.

The practical takeaway: use the camera confidently at 40 meters, but do not treat it as a hard floor. If you are diving to 35 or 38 meters, you have a safety margin. If you are planning a 45-meter dive, the Super Suit is the right choice.

When the waterproof rating fails

The Hero 4 will leak if the seals are damaged or if you have opened the camera body. Common ways the waterproofing breaks are dropping the camera hard enough to crack the lens, opening the USB port door and not seating it fully, or leaving the battery compartment slightly ajar.

If you have dropped the camera or suspect the seals are compromised, test it in a shallow bathtub or pool before taking it to depth. Fill a clear container with water, submerge the camera for 30 seconds, and check for bubbles or water inside the lens. If you see either, do not use it underwater until you have had it inspected or repaired.

Salt water does not break the waterproof seals, but it will corrode metal parts if you do not rinse the camera with fresh water when ready after use. Rinse the entire body, the USB port, and the lens with tap water and let it dry completely before storing.

Using the Super Suit for deeper water

The GoPro Super Suit is a hard plastic housing that wraps around the Hero 4 and extends the waterproof rating to 60 meters. It adds bulk and weight, and it requires you to mount the camera inside before you enter the water — you cannot swap housings mid-dive.

The Super Suit also changes how light enters the lens. The clear front panel is thicker than the camera's lens, which can cause slight distortion or reduce image sharpness compared to shooting without the housing. For most underwater filming, the difference is minor, but if you are shooting in very clear water or need maximum detail, test the housing in shallow water first.

Freshwater versus saltwater use

The Hero 4 is equally waterproof in freshwater and saltwater at the same depth. The waterproof seals do not care whether the water is salty or not. What matters is the depth and the pressure it creates.

Saltwater is harder on the camera after use because salt crystals corrode exposed metal — the USB port, the mounting bracket, and any small metal fasteners. Freshwater does not corrode as quickly, but you should still rinse the camera after any underwater use. Rinse with tap water, dry it with a soft cloth, and store it in a dry place.

Condensation inside the lens after temperature changes

If you take the Hero 4 from cold water to a warm room, condensation can form inside the lens. This happens because the sealed camera traps cold air inside, and when that air warms up, moisture condenses on the glass. The condensation usually clears on its own as the camera reaches room temperature, but it can take 30 minutes to an hour.

To speed up the process, leave the camera in a warm room with the lens cap off (if you have one) and let air circulate around it. Do not use heat sources like a hair dryer, which can damage the lens coating. If condensation appears regularly or does not clear after an hour, the seals may be leaking slightly and the camera should be inspected.

Frequently Asked Questions

Can I use the Hero 4 in a swimming pool?

Yes. A swimming pool is well within the 40-meter rating. Chlorine and pool chemicals do not damage the waterproof seals, but rinse the camera with fresh water afterward to prevent corrosion of any exposed metal parts.

What happens if I accidentally submerge it deeper than 40 meters?

Water pressure increases with depth, and at depths beyond 40 meters the seals may not hold. Water can enter the camera and damage the electronics. If this happens, do not try to turn the camera on — power and water together cause short circuits. Let it dry completely in a warm room for 24 to 48 hours, then have it inspected before use.

Does the waterproof rating change if the camera is older?

The seals degrade over time, especially if the camera has been used in saltwater many times or stored in damp conditions. An older Hero 4 that has been well maintained will still meet the 40-meter rating, but one that has been exposed to salt and moisture repeatedly may not. If you own an older camera and plan deep dives, test it in shallow water first.

Do I need to remove the battery before rinsing with fresh water?

No. The battery compartment is sealed, and fresh water will not reach it. You can rinse the entire camera under tap water without opening any doors. Just make sure the USB port door and any other compartments are fully closed before you rinse.